NordicTrack Cxt 930 English Manual - Page 8

Installing The Receiver For The Optional Chest Pulse Sensor

Get NordicTrack Cxt 930 PDF manuals and user guides View all NordicTrack Cxt 930 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

8. Apply a small amount of the included Teflon® lubricant to a paper towel. Rub a thin film of the lubricant onto the Chrome Tubes (21) on the Left and Right Spring Arms (3, 4). Next, slide the Left Upper Body Arm (7), which is marked with a sticker, onto the Chrome Tube on the Left Spring Arm. Slide the Right Upper Body Arm (75) onto the Chrome Tube on the Right Spring Arm. Make sure that the Upper Body Arms are on the correct sides-the upper ends should bend in the direction shown by the arrows. Next, slide an Axle Cover (74) onto the post on each Upper Body Arm. Apply grease to the Arm Axle (19). Insert the Arm Axle into the right Axle Cover (74) and the Right Upper Body Arm (75). Next, insert the Arm Axle into the Upright (2) until the left end of the Arm Axle is flush with the left side of the Upright. Then, insert the Arm Axle into the left Axle Cover (74) and the Left Upper Body Arm (7). Center the Arm Axle (19). Using the included pedal tool, tap two Push Nuts (15) about 1/8" onto each end of the Arm Axle. Make sure that the Push Nuts are turned as shown in the inset drawing. (Note: It may be helpful if another person holds a block of wood against one end of the Arm Axle while you tap Push Nuts onto the other end.) Then, press an Axle Cap (34) onto each end of the Arm Axle. 8 74 19 74 7 34 15 Grease Post 21 Pedal Tool 15 19 75 34 15 2 21 4 3 9. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may be left over after assembly is completed. INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR If you purchase the optional chest pulse sensor (refer to page 20), follow the steps below to install the receiver and the short jumper wire included with the chest pulse sensor. 1. Remove the four indicated screws from the back of the Console (87). Lift off the front of the Console. 1 Screws 87 2. Peel the paper off the adhesive pad on the back of the receiver (A). Orient the receiver exactly as shown, and press it onto the Console (87) in the indicated location. Connect the short jumper wire (B) to the wire on the receiver (A). Plug the other end of the short jumper wire into either of the indicated jacks on the Console (87). Note: The included long jumper wire is not needed. Refer to step 1 above. Reattach the front of the Console (87) with the four screws. Make sure that no wires are pinched. 8 2 Jacks B 87 A Cylinder

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
8
9.
Make sure that all parts of the elliptical crosstrainer are properly tightened.
Note: Some hardware may
be left over after assembly is completed.
8.
Apply a small amount of the included Teflon
®
lubricant
to a paper towel. Rub a thin film of the lubricant onto
the Chrome Tubes (21) on the Left and Right Spring
Arms (3, 4). Next, slide the Left Upper Body Arm (7),
which is marked with a sticker, onto the Chrome Tube
on the Left Spring Arm. Slide the Right Upper Body
Arm (75) onto the Chrome Tube on the Right Spring
Arm.
Make sure that the Upper Body Arms are on
the correct sides—the upper ends should bend in
the direction shown by the arrows.
Next, slide an
Axle Cover (74) onto the post on each Upper Body Arm.
Apply grease to the Arm Axle (19). Insert the Arm Axle
into the right Axle Cover (74) and the Right Upper Body
Arm (75). Next, insert the Arm Axle into the Upright (2)
until the left end of the Arm Axle is flush with the left
side of the Upright. Then, insert the Arm Axle into the
left Axle Cover (74) and the Left Upper Body Arm (7).
Center the Arm Axle (19). Using the included pedal
tool, tap two Push Nuts (15)
about 1/8”
onto each end
of the Arm Axle. Make sure that the Push Nuts are
turned as shown in the inset drawing. (Note: It may be
helpful if another person holds a block of wood against
one end of the Arm Axle while you tap Push Nuts onto
the other end.) Then, press an Axle Cap (34) onto each
end of the Arm Axle.
8
21
21
2
74
Post
Grease
74
19
34
34
15
15
7
4
75
Pedal Tool
15
19
INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
If you purchase the optional chest pulse sensor (refer to
page 20), follow the steps below to install the receiver and
the short jumper wire included with the chest pulse sensor.
1.
Remove the four indicated screws from the back of the
Console (87). Lift off the front of the Console.
2.
Peel the paper off the adhesive pad on the back of the
receiver (A). Orient the receiver exactly as shown, and
press it onto the Console (87) in the indicated location.
Connect the short jumper wire (B) to the wire on the
receiver (A). Plug the other end of the short jumper wire
into either of the indicated jacks on the Console (87).
Note: The included long jumper wire is not needed.
Refer to step 1 above. Reattach the front of the
Console (87) with the four screws.
Make sure that no
wires are pinched.
A
87
Jacks
87
Screws
1
B
Cylinder
2
3