NordicTrack E 9.0 Elliptical English Manual - Page 7

Orient the Rear Stabilizer Cover 2 as shown.

Get NordicTrack E 9.0 Elliptical PDF manuals and user guides View all NordicTrack E 9.0 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

3. Remove the screws (not shown) and the shipping bracket (not shown) from the rear of the 3 Frame (1). Discard the screws. With the help of a second person, place the ship- ping bracket (not shown) under the rear of the Frame (1). Have the second person hold the Frame to prevent it from tipping while you 5 complete this step. Orient the Rear Stabilizer (5) so that the welded tubes are in the locations shown. Attach the Rear Stabilizer (5) to the Frame (1) with two M10 x 75mm Screws (119). 119 Then, remove and discard the shipping bracket (not shown). 4. Orient the Rear Stabilizer Cover (2) as shown. 4 Press the Mounts (117) on the underside of the Rear Stabilizer Cover (2) into the Rear Stabilizer (5). Then, press the Rear Stabilizer Cover into place. 1 Welded Tubes 2 117 5 5. Have a second person hold the Upright (4) near the Frame (1). 5 See the inset drawing. Locate the wire tie in the lower end of the Upright (4). Tie the wire tie to the Main Wire (110). Then, pull the upper end of the wire tie until the Main Wire is routed through 4 the Upright. Tip: To prevent the Main Wire (110) from fall- ing into the Upright (4), secure the Main Wire with the wire tie. 110 1 Wire Tie 7 Wire Tie 110

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
7
3
5
1
119
Welded Tubes
3.
Remove the screws (not shown) and the ship-
ping bracket (not shown) from the rear of the
Frame (1). Discard the screws.
With the help of a second person, place the ship-
ping bracket (not shown) under the rear of the
Frame (1).
Have the second person hold the
Frame to prevent it from tipping while you
complete this step.
Orient the Rear Stabilizer (5) so that the welded
tubes are in the locations shown.
Attach the Rear Stabilizer (5) to the Frame (1)
with two M10 x 75mm Screws (119).
Then, remove and discard the shipping bracket
(not shown).
4
5
2
117
4.
Orient the Rear Stabilizer Cover (2) as shown.
Press the Mounts (117) on the underside of the
Rear Stabilizer Cover (2) into the Rear Stabilizer
(5). Then, press the Rear Stabilizer Cover into
place.
5.
Have a second person hold the Upright (4) near
the Frame (1).
See the inset drawing.
Locate the wire tie in the
lower end of the Upright (4). Tie the wire tie to
the Main Wire (110). Then, pull the upper end of
the wire tie until the Main Wire is routed through
the Upright.
Tip: To prevent the Main Wire (110) from fall-
ing into the Upright (4), secure the Main Wire
with the wire tie
.
5
1
4
110
Wire
Tie
Wire
Tie
110