NordicTrack E 9.5 I Elliptical English Manual - Page 27

Maintenance And Troubleshooting

Get NordicTrack E 9.5 I Elliptical PDF manuals and user guides View all NordicTrack E 9.5 I Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Next, using a standard Regular maintenance is important for optimal screwdriver, remove performance and to reduce wear. Inspect and properly the left Disc (71). tighten all parts each time the elliptical is used. Replace any worn parts immediately. 71 To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. CONSOLE TROUBLESHOOTING Note: For clarity, the left shield and the left disc ring are shown removed in the drawing below. If the console does not turn on, make sure that the power cord is fully plugged in. Locate the Reed Switch (38). Turn the Pulley (19) until a Magnet (43) is aligned with the Reed Switch. If lines appear in the console display, see HOW TO CHANGE CONSOLE SETTINGS on page 25 and adjust the contrast level of the display. 19 If the console does not display your heart rate when you hold the handgrip heart rate monitor, or if the displayed heart rate appears to be too high or too low, see step 5 on page 22. INCLINE SYSTEM TROUBLESHOOTING If the ramp does not move to the correct incline level, see HOW TO CHANGE CONSOLE SETTINGS on page 25 and calibrate the incline system. 38 43 101 HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, first press the power switch to the off position and unplug the power cord. Slightly loosen the indicated M4 x 16mm Screw (101). Slide the Reed Switch (38) slightly closer to or away from the Magnet (43), and then retighten the Screw. Then, plug in the power cord, press the power switch to the reset position, and rock the Pulley (19) forward and backward just enough that the Magnet passes the Reed Switch repeatedly. Repeat these actions until the console displays correct feedback. When the reed switch is correctly adjusted, press the power switch to the off position, unplug the power cord, and reattach the left disc. Then, plug in the power cord. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
27
MAINTENANCE
Regular maintenance is important for optimal
performance and to reduce wear. Inspect and properly
tighten all parts each time the elliptical is used.
Replace any worn parts immediately.
To clean the elliptical, use a damp cloth and a small
amount of mild soap.
IMPORTANT: To avoid damage
to the console, keep liquids away from the console
and keep the console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console does not turn on, make sure that the
power cord is fully plugged in.
If lines appear in the console display, see HOW TO
CHANGE CONSOLE SETTINGS on page 25 and
adjust the contrast level of the display.
If the console does not display your heart rate when
you hold the handgrip heart rate monitor, or if the dis-
played heart rate appears to be too high or too low, see
step 5 on page 22.
INCLINE SYSTEM TROUBLESHOOTING
If the ramp does not move to the correct incline level,
see HOW TO CHANGE CONSOLE SETTINGS on
page 25 and calibrate the incline system.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first
press the power switch to the off posi
-
tion and unplug the power cord.
Next, using
a standard
screwdriver, remove
the left Disc (71).
Note: For clarity, the left shield and the left disc ring are
shown removed in the drawing below.
Locate the Reed Switch (38). Turn the Pulley (19) until
a Magnet (43) is aligned with the Reed Switch.
Slightly loosen the indicated M4 x 16mm Screw (101).
Slide the Reed Switch (38) slightly closer to or away
from the Magnet (43), and then retighten the Screw.
Then, plug in the power cord, press the power switch
to the reset position, and rock the Pulley (19) forward
and backward just enough that the Magnet passes the
Reed Switch repeatedly.
Repeat these actions until the console displays correct
feedback. When the reed switch is correctly adjusted,
press the power switch to the off position, unplug the
power cord, and reattach the left disc. Then, plug in the
power cord.
38
101
19
43
MAINTENANCE AND TROUBLESHOOTING
71