NordicTrack Elliptical E7.5 User Manual - Page 8

Assemble the Left Upper Body Arm 9

Get NordicTrack Elliptical E7.5 PDF manuals and user guides View all NordicTrack Elliptical E7.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Identify the Right Upper Body Arm (8) and the Right Upper Body Leg (6) and orient them as 4 shown. Insert the Right Upper Body Arm (8) into the Right Upper Body Leg (6). Attach the Right Upper Body Arm (8) with three M8 x 45mm Bolts (104) and three M8 Locknuts (105). Make sure that the Locknuts are inside the hexagonal holes. Do not fully tighten the Bolts yet. Assemble the Left Upper Body Arm (9) and the Left Upper Body Leg (7) in the same way. 9 104 105 7 8 104 105 104 Hexagonal Holes 6 5. Using a small plastic bag to keep your fingers clean, apply a generous amount of the included grease to the Upright Axle (48) and to two M17 x 27mm Wave Washers (88). Tip: Avoid damaging the Upright Wire (60). Insert the Upright Axle (48) through the Upright (5) and center it. Slide an M17 x 27mm Wave Washer (88) onto each side of the Upright Axle. Slide the Right and Left Upper Body Arms (8, 9) onto the right and left sides of the Upright Axle (48). Tighten an M8 x 16mm Screw (102) and an M8 x 25mm x 1.5mm Washer (126) into each end of the Upright Axle (48) at the same time. 5 102 126 Avoid damaging the Upright Wire (60) 9 60 88 48 Grease 5 88 8 126 102 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
8
5
4
5.
Using a small plastic bag to keep your fingers
clean, apply a generous amount of the included
grease to the Upright Axle (48) and to two M17 x
27mm Wave Washers (88).
Tip: Avoid damaging the Upright Wire (60).
Insert the Upright Axle (48) through the Upright
(5) and center it. Slide an M17 x 27mm Wave
Washer (88) onto each side of the Upright Axle.
Slide the Right and Left Upper Body Arms
(8, 9) onto the right and left sides of the Upright
Axle (48).
Tighten an M8 x 16mm Screw (102) and an M8
x 25mm x 1.5mm Washer (126) into each end of
the Upright Axle (48)
at the same time.
9
8
7
Hexagonal
Holes
104
104
104
105
105
6
9
126
126
8
5
102
102
48
Grease
60
88
88
4.
Identify the Right Upper Body Arm (8) and the
Right Upper Body Leg (6) and orient them as
shown.
Insert the Right Upper Body Arm (8) into the
Right Upper Body Leg (6).
Attach the Right Upper Body Arm (8) with three
M8 x 45mm Bolts (104) and three M8 Locknuts
(105).
Make sure that the Locknuts are inside
the hexagonal holes. Do not fully tighten the
Bolts yet.
Assemble the Left Upper Body Arm (9) and
the Left Upper Body Leg (7) in the same way.
Avoid damaging the
Upright Wire (60)