NordicTrack T 14.2 English Manual - Page 8

See the inset drawing., Be careful not to pinch the wires., do not, fully tighten the Screws yet.,

Get NordicTrack T 14.2 PDF manuals and user guides View all NordicTrack T 14.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

3. Identify the Left Upright (84). Have a second person hold the Left Upright near the Base (29). 3  See the inset drawing. Tie the wire tie in the Left Upright (84) securely around the end of the Upright Wire (91). Then, pull the other end of the wire tie until the Upright Wire is routed through the Left Upright. 84 91 84 Wire Tie Wire Tie 91 91 29 4. Hold the Left Upright (84) against the Base (29). Be careful not to pinch the wires. If neces- 4 sary, position the base ground wire (A) in the hole in the side of the Left Upright. Insert two 3/8" x 2 3/4" Screws (22) with two 3/8" Star Washers (10) and two 3/8" x 1 1/4" Screws (3) with two 3/8" Star Washers (10) into the Left Upright. Partially tighten the 3/8" x 2 3/4" Screws (22) and the 3/8" x 1 1/4" Screws (3) until the heads of the Screws touch the Left Upright (84); do not 84 fully tighten the Screws yet. Note: It may be helpful to use the short hex key (B) on the Screw 22 shown. Attach the Right Upright (not shown) in the B same way. Note: There are no wires on the right side. 10 10 A 3 10 29 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
8
3.
Identify the Left Upright (84). Have a second
person hold the Left Upright near the Base (29).
See the inset drawing.
Tie the wire tie in the
Left Upright (84) securely around the end of the
Upright Wire (91). Then, pull the other end of the
wire tie until the Upright Wire is routed through
the Left Upright.
91
3
91
84
Wire
Tie
Wire
Tie
84
29
91
4.
Hold the Left Upright (84) against the Base (29).
Be careful not to pinch the wires.
If neces-
sary, position the base ground wire (A) in the
hole in the side of the Left Upright. Insert two
3/8" x 2 3/4" Screws (22) with two 3/8” Star
Washers (10) and two 3/8" x 1 1/4" Screws (3)
with two 3/8" Star Washers (10) into the Left
Upright.
Partially tighten the 3/8" x 2 3/4" Screws (22)
and the 3/8" x 1 1/4" Screws (3) until the heads
of the Screws touch the Left Upright (84);
do not
fully tighten the Screws yet.
Note: It may be
helpful to use the short hex key (B) on the Screw
shown.
Attach the Right Upright (not shown) in the
same way.
Note: There are no wires on the right
side.
84
29
4
3
22
10
A
10
B
10