NordicTrack T 6.3 Treadmill User Manual - Page 19

adjust the incline of the treadmill to zero.

Get NordicTrack T 6.3 Treadmill PDF manuals and user guides View all NordicTrack T 6.3 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

5. Follow your progress with the displays. When you select the manual mode, a track representing 1/4 mile (400 m) will appear in the matrix. As you walk or run on the treadmill, the indicators around the track will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession. The lower left display can show the elapsed time and the distance that you have walked or run during your workout. Each time you change the incline, the display will show the incline setting for a few seconds. Note: When a workout is selected, the display will show the time remaining in the workout instead of the elapsed time. The lower right display can show the speed of the walking belt and the approximate number of calories that you have burned during your workout. The display will also show your heart rate when you use the handgrip heart rate monitor (see step 6). The upper display can show the elapsed time, the distance that you have walked or run, the approximate number of calories you have burned, or the speed of the walking belt. Press the Priority Display button repeatedly until the upper display shows the information that you are most interested in viewing. Note: While information is shown in the upper display, the same information will not be shown in the lower left or lower right display. To reset the displays, press the Stop button, remove the key, and then reinsert the key. 6. Measure your heart rate if desired. Before using the handgrip heart rate monitor, remove the sheets of plastic from the metal contacts on the pulse bar. In addition, make sure that your hands are clean. Contacts To measure your heart rate, stand on the foot rails and hold the pulse bar with your palms on the metal contacts for approximately ten seconds; avoid moving your hands. When your pulse is detected, a heart symbol in the calorie display will ash each time your heart beats, one or two dashes will appear, and then your heart rate will be shown. For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds. 7. When you are nished exercising, remove the key from the console. Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to zero. The incline must be at zero or you may damage the treadmill when you fold it to the storage position. Next, remove the key from the console and put it in a secure place. When you are nished using the treadmill, press the power switch into the off position and unplug the power cord. IMPORTANT: If you do not do this, the treadmill’'s electrical components may wear prematurely. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
19
5.
Follow your progress with the displays.
When you select the
manual mode, a track
representing 1/4 mile
(400 m) will appear in the
matrix. As you walk or
run on the treadmill, the
indicators around the track will appear in succes-
sion until the entire track appears. The track will
then disappear and the indicators will again begin
to appear in succession.
The lower left display can
show the elapsed time
and the distance that you
have walked or run during
your workout. Each time
you change the incline,
the display will show the incline setting for a few
seconds. Note: When a workout is selected, the
display will show the time remaining in the workout
instead of the elapsed time.
The lower right display
can show the speed
of the walking belt and
the approximate num-
ber of calories that you
have burned during your
workout. The display will also show your heart rate
when you use the handgrip heart rate monitor (see
step 6).
The upper display can
show the elapsed time,
the distance that you
have walked or run, the
approximate number of
calories you have burned,
or the speed of the walking belt. Press the Priority
Display button repeatedly until the upper display
shows the information that you are most interested
in viewing. Note: While information is shown in the
upper display, the same information will not be
shown in the lower left or lower right display.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
6.
Measure your heart rate if desired.
Before using the handgrip heart rate monitor, re-
move the sheets of plastic from the metal contacts
on the pulse bar. In addition, make sure that your
hands are clean.
To measure your heart rate,
stand on the foot
rails
and hold the pulse bar with your palms on
the metal contacts for approximately ten seconds;
avoid moving your hands.
When your pulse is
detected, a heart symbol in the calorie display
will
ash each time your heart beats, one or two
dashes will appear, and then your heart rate will be
shown.
For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
7.
When you are
nished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to zero.
The
incline must be at zero or you may damage the
treadmill when you fold it to the storage posi-
tion.
Next, remove the key from the console and
put it in a secure place.
When you are
nished using the treadmill, press
the power switch into the off position and unplug
the power cord.
IMPORTANT: If you do not do
this, the treadmill°s electrical components may
wear prematurely.
Contacts