Home » Oki Manuals » Printers » Oki B8300n » Manual Viewer

Oki B8300n Guide: User's, B8300 - Page 56

I/O timeout, Port switching, Network settings, IP address setting, Enable TCP/IP, Enable NetWare

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

I/O timeout This program is used to set the length of time to wait for an I/O to complete a job on the parallel port or the network port. If the data stream to the port does not transmit data for a length of time exceeding the timeout, the job will cancel and the next job will start processing. The allowable range of the time is 1 to 999 seconds. Port switching This program is used to set the switching method of the parallel port and network port of this printer. Setting item PER JOB TIMEOUT PARALLEL OFF NETWORK OFF Description After a print job is completed, automatic port selection state will be restored. After I/O timeout time elapses, automatic port selection state will be restored. Printing from the parallel port is disabled. Printing from the network port is disabled. Network settings These programs are set when this product is used as a network printer. After each program is set, exit the key operator program, turn off the main switch, and then turn on the main switch again after a while. The program that has been set will be effective at this time. > Before setting and modification of any network settings, be sure to consult your network administrator. IP address setting When using this product on a network that uses the TCP/IP protocol, use this program to set the IP address (IP address, IP subnet mask, and IP gateway) of this product. The program is set to ENABLE DHCP by factory default setting, which has the IP address setting obtained automatically. When using this product on a network that uses the TCP/IP protocol, also set the program Enable TCP/IP. Enable TCP/IP When using this product on a network that uses the TCP/IP protocol, set this program. Also set the IP address using the program IP address setting. Enable NetWare When using this product on a network that uses the Novell NetWare protocol, set this program. Enable EtherTalk When using this product on a network that uses the EtherTalk protocol, set this program. Enable NetBEUI When using this product on a network that uses the NetBEUI protocol, set this program. Reset the NIC This program is used to reset all configurable items of the NIC to their factory default settings. 55 - Key operator programs

Section	Page
CONTENTS	2
Warranty	6
Trademark Acknowledgments	6
Before you do anything please read this	7
Installation requirements	7
Moving the machine	8
General warnings	9
Laser cautions	10
Overview	12
Introduction	12
Original and paper sizes	12
Main Features	13
Energy saving features	13
Part Names and Functions	14
Exterior	14
Interior	15
Part names and functions	16
Peripheral devices	16
Operation panel of the main unit	18
Menu group and Key explanations main unit operation panel	19
Cancelling a print job and deleting print data	20
To delete print data of a reserved job (jobs stored in the printer)	20
Loading Paper	21
Loading paper in paper tray 1	21
Changing the paper size in paper tray 1	21
Specifications of paper trays	22
Applicable plain paper	23
Applicable special paper	23
Setting the paper size and type from the operation panel on the main printer	24
Loading paper in the multi-purpose drawer	25
Fusing unit pressure adjusting levers	26
Loading transparency film	27
Specifications (multi-purpose drawer)	27
Loading paper in the stand/3 x 500 sheet paper drawer	27
Specifications (stand/3 x 500 sheet paper drawer)	27
Loading paper in the stand/MPD and 2000 sheet paper drawer	28
lUpper paper tray	28
lLower paper tray	28
Storage of supplies	29
lProper storage	29
lStore paper in the wrapper and lying flat.	29
Supply list	29
Adding toner	30
Developer cartridge replacement	32
Printing from a computer	34
Connecting this machine as a local printer	34
Software for Windows	34
Installing printer drivers and utilities	35
Uninstalling printer drivers and printer utilities	35
Plug and play or Add Printer Wizard	35
Setting drivers using Windows	37
Printer configuration through a network	38
Accessing Web pages and displaying Help	38
Web page items and functions	39
Access setup	39
IP addresses, trap community, and authentic community are set here.	39
Job control	40
Job control operation	40
Hold job list	41
When the machine is being operated from the operator panel:	41
Printer account control	42
Using the printer with a Macintosh	43
PPD files	43
OKI PPD Utility	43
Display fonts	43
Installing the utilities	43
Selecting the printer	44
Paper settings	44
Print settings	44
Installing the display fonts	45
Using the PPD Utility	45
Configuration settings	46
Operation procedure common to all printer configuration settings	46
Default settings	47
Smoothing	47
Copies	47
Orientation	47
Default paper size	47
Default paper type	47
Default output tray	47
PCL settings	47
PostScript settings	47
Custom settings	48
Operation procedure common to all printer configuration settings	48
Setting items	49
Total count	49
List print	49
Clock	49
Tray settings	49
Auto tray switching	49
Key operator programs	50
Using the programs	50
Structure of the setting method for key operator programs	51
Key operator programs	53
Account control	53
Auditing mode	53
Print per account	53
Reset account	53
Account number control	53
No print if ACC’T # invalid	53
Energy save	53
Auto power shut-off timer	53
Auto power shut-off	53
Preheat mode	53
Toner save	53
Operator panel settings	54
Auto clear setting	54
Message display time	54
Language setting	54
Device settings	54
Disable duplex unit	54
Disable stapler unit	54
Disable paper desk drawers	54
Disable finisher	54
Disable mail-bin stacker	54
Saddle stitch adjust	54
Print key operator programs list	54
Key operator code change	55
Default settings	55
Print density level	55
Disable notice page printing	55
Disable test page printing	55
A4/LT auto select	55
Interface settings	55
Hexadecimal dump mode	55
PDL for parallel port	55
PDL for network port	55
I/O timeout	56
Port switching	56
Network settings	56
IP address setting	56
Enable TCP/IP	56
Enable NetWare	56
Enable EtherTalk	56
Enable NetBEUI	56
Reset the NIC	56
Initialize/store settings	57
Restore factory defaults	57
Store current configuration	57
Restore configuration	57
Key Operator Code	57
Troubleshooting and maintenance	58
Misfeed removal	58
General misfeed removal procedure	58
Misfeed in the paper feed area	59
Misfeed in paper tray 1	59
Misfeed in multi-purpose drawer	60
Misfeed in the stand/3 x 500 sheet paper drawer	60
Misfeed in the stand/MPD and 2000 sheet paper drawer	60
Misfeed in the transport area, fusing area and exit area	61
Misfeed in the duplex module	62
Misfeed in the bypass tray	62
Troubleshooting	63
Duplex module	66
Part names	66
Specifications	66
Loading paper in the bypass tray	67
Setting the printer driver for duplex module, bypass tray and exit tray	68
Two-sided printing	68
Using the bypass tray	68
Using the exit tray mounted to the duplex module	68
Troubleshooting the duplex module	69
Mail-bin stacker	70
Part names	70
Specifications	70
Specifying mail bins to receive printed output	71
Using the mail-bin stacker	71
Assign users to mail bins	71
Specifying a mail bin	71
Misfeed in the mail-bin stacker	72
Finisher	73
Part names	73
Specifications	73
Finisher functions	74
Using the finisher functions	74
Staple cartridge replacement	75
Checking the stapler unit	76
Misfeed in the finisher	77
Troubleshooting finisher problems	78
Stapling position quick reference guide for duplex output	79
Saddle stitch finisher	80
Part names	80
Specifications	80
Supplies	81
Saddle stitch finisher functions	81
Staple cartridge replacement and staple jam removal	83
Staple jam removal	84
Disposal of hole punch scrap	85
Misfeed in the saddle stitch finisher	86
Stapling position quick reference guide for duplex output	88
Relationship between print image and saddle stitch	89
Printer specifications	90
List of principal printer driver functions	91
List of combination of peripheral devices	92
Notice page printing	93
Print area	94

Match case Limit results 1 per page

55 — Key operator programs

I/O timeout

This program is used to set the length of time to

wait for an I/O to complete a job on the parallel

port or the network port.

If the data stream to the port does not transmit

data for a length of time exceeding the timeout,

the job will cancel and the next job will start

processing.

The allowable range of the time is 1 to 999

seconds.

Port switching

This program is used to set the switching

method of the parallel port and network port

of this printer.

Network settings

These programs are set when this product is

used as a network printer.

After each program is set, exit the key operator

program, turn off the main switch, and then

turn on the main switch again after a while. The

program that has been set will be effective at

this time.

Before setting and modification of any

network settings, be sure to consult your

network administrator.

IP address setting

When using this product on a network that uses

the TCP/IP protocol, use this program to set the

IP address (IP address, IP subnet mask, and IP

gateway) of this product. The program is set to

ENABLE DHCP

by factory default setting, which

has the IP address setting obtained

automatically. When using this product on a

network that uses the TCP/IP protocol, also set

the program

Enable TCP/IP

When using this product on a network that uses

the TCP/IP protocol, set this program. Also set

the IP address using the program

IP address

setting

Enable NetWare

When using this product on a network that uses

the Novell NetWare protocol, set this program.

Enable EtherTalk

When using this product on a network that uses

the EtherTalk protocol, set this program.

Enable NetBEUI

When using this product on a network that uses

the NetBEUI protocol, set this program.

Reset the NIC

This program is used to reset all configurable

items of the NIC to their factory default

settings.

Setting item

Description

PER JOB

After a print job is completed,

automatic port selection state

will be restored.

TIMEOUT

After I/O timeout time elapses,

automatic port selection state

will be restored.

PARALLEL OFF

Printing from the parallel port is

disabled.

NETWORK OFF

Printing from the network port is

disabled.