Onkyo TX-NR609 Owner Manual - Page 73
USB Device Playback, Others, The functions System On/Auto Power On - network not working
View all Onkyo TX-NR609 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 73 highlights
USB Device Playback ■ Can't access the music files on a USB device Make sure the USB device is plugged in properly. - The AV receiver supports USB devices that support - the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class. USB memory devices with security functions cannot - be played. Others ■ Standby power consumption In the following cases, the power consumption in 18, 56, standby mode may reach up to a maximum of 43 W: 57, 58 - You are using the Universal Port jack. - "Network Control" is set to "Enable" in the "Network" setting. - "HDMI Control (RIHD)" setting is set to "On". (Depending on the TV status, the AV receiver will enter standby mode as usual.) - The "HDMI Through" setting is set to other than "Off". ■ The sound changes when I connect my headphones When a pair of headphones is connected, the - listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio (European, Australian and Asian models). ■ The speaker distance cannot be set as required In some cases, corrected values suitable for home - theater use may be set automatically. ■ The display doesn't work (European, Australian and Asian models) The - display is turned off when the Pure Audio listening mode is selected. ■ How do I change the language of a multiplex source Use the "Multiplex" setting on the "Audio Adjust" 49 menu to select "Main" or "Sub". ■ When performing "Automatic Speaker Setup", the measurement fails showing the message "Ambient noise is too high." This can be caused by a malfunction in your speaker - unit. Check if the unit produces normal sounds. ■ The following settings can be made for the composite video inputs You must use the buttons on the unit to make these settings. On the AV receiver, press the input selector for the input source that you want to set and the SETUP button simultaneously. While holding down the input selector button, press SETUP until "Video ATT:ON" appears on the display. Then, release both buttons. To reactivate the setting, repeat the above process so that "Video ATT:OFF" appears on the display, and release the buttons. • Video Attenuation This setting can be made for the BD/DVD, VCR/DVR, CBL/SAT or GAME input. If you have a game console connected to the composite video input, and the picture isn't very clear, you can attenuate the gain. Video ATT:OFF: (default). Video ATT:ON: Gain is reduced by 2 dB. ■ If the picture on your TV/monitor connected to HDMI OUT is unstable, try switching the DeepColor function off To turn off the DeepColor function, simultaneously press the CBL/SAT and ON/STANDBY buttons on the AV receiver. While holding down CBL/SAT, press ON/STANDBY until "Off" appears on the display. Then, release both buttons. To reactivate the DeepColor function, repeat the above process until "On" appears on the display and release the buttons. The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in. ■ The V functions don't work To use V, you must make an V connection and 20 an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally. ■ The functions System On/Auto Power On and Direct Change don't work for components connected via V These functions don't work when Zone 2 is turned 20 on. Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit's malfunction. Before you record important data, make sure that the material will be recorded correctly. Before disconnecting the power cord from the wall outlet, set the AV receiver to standby. En 73