Onkyo TX SR507 Owner Manual - Page 40

Speaker Settings, Use the Up and Down - bi amp

Get Onkyo TX SR507 - AV Receiver PDF manuals and user guides
UPC - 751398008658
View all Onkyo TX SR507 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

First Time Setup-Continued Speaker Settings 4 If you change these settings, you must run the Audyssey 2EQ™ Room Correction and Speaker Setup again (see page 37). If the impedance of any speaker is 4 ohms or more but less than 6, set the Speaker Impedance to 4 ohms. North American and Taiwan models do not support speakers with an impedance of less than 6 ohms. To use bi-amping, you must change the Speaker Type setting. For hookup information, see page 19. Notes: • When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room. 5 • Before you change these settings, turn down the volume. 1 Press the [RECEIVER] button, followed by the [SETUP] button. 2 Use the Up and Down [R]/[X] buttons to select "2. Speaker Setup", and then press [ENTER]. 6 3 Use the Up and Down [R]/[X] buttons to select "2-1.Sp Settings", and then press [ENTER]. 7 Use the Up and Down [R]/[X] buttons to select "Impedance", and use the Left and Right [F]/[S] buttons to select (not North American and Taiwan models): 4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms. Use the Up and Down [R]/[X] buttons to select "Sp Type", and use the Left and Right [F]/[S] buttons to select (TX-SR577 only): Normal: Select this if you've connected your front speakers normally. Bi-Amp:Select this if you've connected your front speakers for bi-amped operation. Note: Powered Zone2 cannot be used if "Sp Type" is set to "Bi-Amp". Use the Up and Down [R]/[X] buttons to select "SB/FH", and then use the Left and Right [F]/[S] buttons to select (TX-SR577 only): FrontHigh: Select this if you've connected your front high speakers to the SURR BACK L/R terminal posts. SurrBack: Select this if you've connected your surround back speakers to the SURR BACK L/R terminal posts. Note: If the "Sp Type" setting is set to "BiAmp", or Powered Zone 2 is set to "Not Act" (page 81), this setting cannot be selected. Press the [SETUP] button. Setup closes. Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
40
First Time Setup
—Continued
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
North American and Taiwan models do not support
speakers with an impedance of less than 6 ohms.
To use bi-amping, you must change the Speaker Type
setting. For hookup information, see page 19.
Notes:
•
When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
•
Before you change these settings, turn down the
volume.
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
2
Use the Up and Down [
q
]/[
w
]
buttons to select “2. Speaker
Setup”, and then press [ENTER].
3
Use the Up and Down [
q
]/[
w
]
buttons to select “2-1.Sp
Settings”, and then press
[ENTER].
If you change these settings, you must run the
Audyssey
2EQ™ Room Correction and Speaker Setup
again (see page 37).
4
Use the Up and Down [
q
]/[
w
]
buttons to select “Impedance”,
and use the Left and Right
[
e
]/[
r
] buttons to select (not
North American and Taiwan
models):
4 ohms:
Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
6 ohms:
Select if the impedances of all
speakers are between 6 and
16 ohms.
5
Use the Up and Down [
q
]/[
w
]
buttons to select “Sp Type”, and
use the Left and Right [
e
]/[
r
]
buttons to select (TX-SR577
only):
Normal:
Select this if you’ve
connected your front speakers
normally.
Bi-Amp:
Select this if you’ve
connected your front speakers
for bi-amped operation.
Note:
Powered Zone2 cannot be used if “Sp
Type” is set to “Bi-Amp”.
6
Use the Up and Down [
q
]/[
w
] but-
tons to select “SB/FH”, and then
use the Left and Right [
e
]/[
r
]
buttons to select (TX-SR577
only):
FrontHigh:
Select this if you’ve con-
nected your front high speak-
ers to the SURR BACK L/R
terminal posts.
SurrBack:
Select this if you’ve con-
nected your surround back
speakers to the SURR BACK
L/R terminal posts.
Note:
If the “Sp Type” setting is set to “Bi-
Amp”, or Powered Zone 2 is set to “Not
Act” (page 81), this setting cannot be
selected.
7
Press the [SETUP] button.
Setup closes.