Optoma HD33 User's Manual
Optoma HD33 Manual
 |
View all Optoma HD33 manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma HD33 manual content summary:
- Optoma HD33 | User's Manual - Page 1
Troubleshooting 42 Image Problems 42 Other Problems 44 Remote Control Problems 44 LED Lighting Messages 45 On Screen Messages 46 Replacing the Lamp 47 Compatibility Modes 49 RS232 Commands and Protocol Function List 52 RS232 Pin Assignments 52 RS232 Protocol Function List 53 Ceiling Mount - Optoma HD33 | User's Manual - Page 2
attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please call Optoma before you send the unit for repair. 7. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could - Optoma HD33 | User's Manual - Page 3
will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. Reset the "Lamp Reset" function from the onscreen display "System|Lamp Setting" menu after replacing the lamp module. When switching the projector off, please ensure the cooling cycle has - Optoma HD33 | User's Manual - Page 4
`` Relative humidity is 10% ~ 85% -- In areas susceptible to excessive dust and dirt. -- Near any appliance generating a strong magnetic field. -- In direct sunlight. Viewing 3D PROJECTOR using the 3D function IMPORTANT SAFETY INFORMATION. READ THE FOLLOWING WARNINGS BEFORE YOU OR YOUR CHILD USE THE - Optoma HD33 | User's Manual - Page 5
extended period of time may damage your eyesight. The ideal viewing distance should be at least three times the screen height. It is recommended that the viewer's eyes are level with the screen. ™™ Watching 3D PROJECTOR while wearing 3D glasses for an extended period of time may cause a headache or - Optoma HD33 | User's Manual - Page 6
beam at all times. Keep your back to the beam as much as possible. ▀■ When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. ▀■ In order to minimize the lamp power, use room blinds to reduce ambient light levels. English 6 - Optoma HD33 | User's Manual - Page 7
is missing, please contact Optoma customer service. NOTE ™™ Due to different applications in each Country, some regions may have different accessories. Projector with lens cap Power Cord 1.8m IR Remote Control 2 × AAA Batteries Documentation: User's Manual Warranty Card Quick Start - Optoma HD33 | User's Manual - Page 8
Introduction Product Overview Main Unit 1 2 3 4 3 6 5 78 6 7 English 6 9 10 11 6 1. Ventilation (outlet) 2. Focus Ring 3. IR Receiver 4. Ventilation (inlet) 5. Zoom Ring 6. Tilt-Adjustment Feet 7. Zoom Lens 8 8. Lens Cap 9. Power Socket 10. Input / Output Connections 11. KensingtonTM - Optoma HD33 | User's Manual - Page 9
Video Input Connector 5. Composite Video Input Connector 6. 3D Sync Out (5V) Connector 7. 12V Trigger Relay (12V, 250mA) 8. Lamp LED (Indicates the projector's lamp status) 9. Temp LED (Indicates the projector's temperature status) 10. Power Socket 11. USB Service 12. RS-232 Connector (9-pin) 13 - Optoma HD33 | User's Manual - Page 10
Remote Control 1 20 19 18 17 16 15 14 13 12 11 21 1. Power On 2. Power Off 3. 16:9 4. Native 2 5. PureEngine 6. 3D Format 3 7. Enter 8. Re-Sync 4 9. VGA Source 5 10. Video Source 11. HDMI 2 Source 6 12. YPbPr Source 13. HDMI 1 Source 7 14. Menu 15. Source 8 16. Lamp - Optoma HD33 | User's Manual - Page 11
Installation Connecting the Projector Connect to Computer/Notebook 3D Glasses MOLEX +12V Output 1 2 34 5 6 HDMI 1 HDMI 2 VGA YPbPr 3D SYNC Out (5V) 12V Trigger YG Pb B Pr R VIDEO SERVICE RS-232 molex 7 POWER R E62405SP NOTE ™™ Due to the difference in applications for each - Optoma HD33 | User's Manual - Page 12
For more detailed information about connecting to the 3D emitter and 3D glasses, please refer to their user's guides. ™™ Use high speed HDMI cable to connect Blue-ray 3D player. ™™ * Optional Accessory 7 3 Composite Video Output DVD Player, Set-top Box, HDTV receiver 1. Power Cord 2. HDMI Cable - Optoma HD33 | User's Manual - Page 13
source and your 3D projector. PlayStation® 3 Games yy Make sure that you have updated your console to the latest software ver- sion in PlayStation® 3. yy Go to the "Settings menu -> Display settings -> Video output -> HDMI". Select "Automatic" and follow the on-screen instructions. yy Insert your - Optoma HD33 | User's Manual - Page 14
Installation 3D Broadcast 3D Blu-ray™ Disc 3D Console Games SKY+HD, cable/satellite box 3D Blu-ray™ Player PlayStation® 3 3D Glasses Full 3D 1080p DLP® Projector English All other product names, company names and trade names used herein are for identifications purposes only and may be - Optoma HD33 | User's Manual - Page 15
refer to 3D glasses user's guide. Using the 3D glasses 1. To turn ON 3D glasses: Press the "Power" button and the LED will flash one time indicating the glasses are ready to use 3D mode. 2. Verify that 3D content is being sent to the projector and signal is compatible with projector specifications - Optoma HD33 | User's Manual - Page 16
. 3. Turn on the lamp by pressing "POWER" button on the back of the projector or pressing " " button on the remote control. The Power LED will remote control to switch between inputs. 3D SYNC Out (5V) 12V Trigger VGA YPbPr NOTE YG Pb B Pr R VIDEO SERVICE RS-232 or ™™ Turn on the projector - Optoma HD33 | User's Manual - Page 17
conditions, the projector can be switched on again after it has cooled down. ™™ When the "TEMP" indicator flashes red, it indicates the fan has failed. ™™ After the projector has cooled down, you can press and hold " " button on the remote control for 10 seconds to leave failure mode to standby - Optoma HD33 | User's Manual - Page 18
as needed. Tilt-Adjustment Feet Tilt-Adjustment Ring Adjusting the Projector's Zoom / Focus You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 4.92 to 32.8 feet (1.0 to 10.0 meters). Focus Ring - Optoma HD33 | User's Manual - Page 19
Installation Adjusting Projection Image Size Top View Screen Screen (W) Side View Projection Distance (D) Projection Distance (D) Screen Screen (H) Offset (Hd) Height Diagonal Width Diagonal length (inch) size of 16:9 Screen 38 45 50 60 70 80 90 100 120 150 200 300 Screen Size W x H - Optoma HD33 | User's Manual - Page 20
User Controls Remote Control Using the Remote Control Power On Turn on the projector. Power Off Turn off the projector. Lamp Mode Increase the brightness of the image. Mode Select the display mode from Cinema, Bright, Photo, Reference, 3D, ISF Day, ISF Night and User. 4:3 Scale the image - Optoma HD33 | User's Manual - Page 21
User Controls Using the Remote Control Enter Confirm your item selection. Source Re-sync Menu HDMI 1 HDMI 2 VGA YPbPr Video Four Directional Select Keys Press "Source" to select an input signal. Automatically synchronizes the projector to the input source. Display or exit the on-screen display - Optoma HD33 | User's Manual - Page 22
Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or Control Panel. 2 When OSD is displayed, use ▲▼ keys to select any item in the - Optoma HD33 | User's Manual - Page 23
3D Menu Location Lamp Settings Projection Test Pattern Background Color 12V Trigger Exit 3D Mode 3D -> 2D 3D Format #5 3D Sync. Invert Exit Lamp Hours Lamp Reminder Lamp Mode Lamp Reset Exit Settings Cinema / Bright / Photo / Reference / 3D / On (2.35:1) / Auto DLP-Link / VESA 3D 3D / L / R Off / - Optoma HD33 | User's Manual - Page 24
Automatic Exit White Level Black Level Saturation Hue IRE Exit Current All Settings English / Deutsch / Français / Italiano / Español vary according to the signal type selected and the projector model you are using. (#1) "Color" and "Tint" are only supported in Video mode. (#2) For HDMI model - Optoma HD33 | User's Manual - Page 25
ISF Night: Optimize the image with the ISF Night mode to be perfectly calibrated and high picture quality. `` User: User's settings. Contrast The contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and - Optoma HD33 | User's Manual - Page 26
User Controls NOTE ™™ "Color" and "Tint" are only supported for composite and component sources. `` Press the ◄ to decrease the contrast. `` Press the ► to increase the contrast. Brightness Adjust the brightness of the image. `` Press - Optoma HD33 | User's Manual - Page 27
The Noise Reduction reduces the amount of visible noise interlaced signals. The range is from "0" to "10". (0: Off) Gamma This allows you to set up gamma curve type. After the initial setup and fine tuning is completed, utilize the Gamma Adjustment steps to optimize your image output. `` Film - Optoma HD33 | User's Manual - Page 28
User Controls IMAGE | Advanced | PureEngine NOTE ™™ While the input source is 120Hz timing, the PureMotion function does not support this timing and will be gray out. PureDetail PureDetail is an edge enhancement tool that enables the edges in the projected image is be enhanced - Optoma HD33 | User's Manual - Page 29
cold temperature, the image looks more blue. (cold image) If set to warm temperature, the image looks more red. (warm image) RGB Gain/Bias Press ► or Blue for brightness (Gain) and contrast (Bias). `` Reset: Choose "Yes" to return the factory default settings for color adjustments. 29 English - Optoma HD33 | User's Manual - Page 30
User Controls NOTE ™™ (*) For HDMI only. Color Space Select an appropriate color matrix type from AUTO, RGB, RGB(0-255)(*) RGB(16-235)(*) or YUV. English 30 - Optoma HD33 | User's Manual - Page 31
User Controls Format external anamorphic lens to display 2.35:1 aspect ratio using full resolution. `` Native: This format displays the original image support anamorphic wide is enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp power and vertical - Optoma HD33 | User's Manual - Page 32
Controls 2.0:1 aspect ratio screen. 2. Switch SuperWide ON. 3. Align the projector image correctly on the screen. 4. Enjoy movies without black bars position vertically. V Keystone Press the ◄ or ► to adjust image distortion vertically 3D Press ► into the next menu and then use ▲ or ▼ to - Optoma HD33 | User's Manual - Page 33
| 3D User Controls NOTE ™™ "3D Format" is only supported on non-HDMI 1.4a 3D timing. ™™ Press "Enter" to select 3D format. 3D Mode `` DLP Link: Select "DLP Link" to use optimized settings for DLP Link 3D Glasses. (please refer to page 15). `` VESA 3D: Select "VESA 3D" to use optimized setting for - Optoma HD33 | User's Manual - Page 34
User Controls NOTE ™™ "3D sync. Invert" function wouldn't save the setting. It will set to "Off" when powers on and changes source. 3D Sync. Invert `` Press the "On" to invert left and right frame contents. `` Press the "Off" for default frame contents. English 34 - Optoma HD33 | User's Manual - Page 35
™™ Rear-Desktop and Rear-Ceiling are to be used with a translucent screen. NOTE ™™ "Test Pattern" function will gray out when 3D is on. Menu Location Choose the menu location on the display screen. Lamp Setting Press ► into the next menu and then use ▲ or ▼ to select item. Projection ` ` Front - Optoma HD33 | User's Manual - Page 36
the "Enter" button on the remote control. Checking an option in the sub-menu will activate the trigger when the corresponding display mode is selected. For the example, 4:3 has been selected - this means that Trigger B will be active when the projector display mode is set to 4:3. The trigger will be - Optoma HD33 | User's Manual - Page 37
" can be indipendently set for 2D and 3D. Lamp Hour Display the cumulative lamp operating time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear up 30 hours before suggested replacement of lamp. Lamp Mode - Optoma HD33 | User's Manual - Page 38
User Controls SETUP Language Choose the multilingual OSD menu. Press ◄ or ► into the sub menu and then use the ▲ or ▼ to ► into the next menu and then use ▲ or ▼ to select item. Press "Select (Enter)" to finalize the selection. The projector will not search inputs that are de-selected. English 38 - Optoma HD33 | User's Manual - Page 39
to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Information Hide `` Press "On" to hide the info message. `` Press "Off" to show the "searching" message. Auto Power Off Set the interval of power-off of the system - Optoma HD33 | User's Manual - Page 40
function, the Frequency and Phase items are grayed out, and if Signal is not automatic, the Frequency and Phase items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. English 40 - Optoma HD33 | User's Manual - Page 41
Appendices SETUP | Signal -Video Source NOTE ™™ "Signal" is not supported when the source is HDMI or DVI-D. ™™ "IRE" is only supported on NTSC signal. White Level Allow user adjust White Level when inputting S-Video or Video/ CVBS signals. Black Level Allow user adjust Black Level when - Optoma HD33 | User's Manual - Page 42
Appendices Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image Problems N o image appears on-screen `` Ensure all the cables and power connections are - Optoma HD33 | User's Manual - Page 43
has slanted sides: `` If possible, reposition the projector so that it is centered on the screen and display in 3D `` Check if the battery of 3D glasses is drained. `` Check if the 3D glasses is turned on. `` When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D Format" button - Optoma HD33 | User's Manual - Page 44
been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section. Remote Control Problems If the remote control does not work `` Check the operating angle of the remote control is within ±15° both horizontally and vertically of on of the IR receivers on the projector - Optoma HD33 | User's Manual - Page 45
Off Off Error (Fan fail) Flashing Off Flashing Error (Over Temp.) Flashing Off Steady light Lamp LED (Orange) Off Off Off Off Steady light Off Off 3D SYNC Out (5V) 12V Trigger VGA YPbPr HDMI 1 Y G HDMI 2 VGA YPbPr Pb B YG 3D SYNC Out (5V) 12V Trigger Pr R VIDEO SERVICE Pb B Pr - Optoma HD33 | User's Manual - Page 46
Appendices On Screen Messages ™™ Power down timer active: ™™ Lamp warning: ™™ Power off: English 46 - Optoma HD33 | User's Manual - Page 47
changing the lamp. Warning: If ceiling mounted, please use caution when opening the lamp access panel. It is recommended to wear safety glasses if changing the bulb when ceiling mounted. "Caution must be used to prevent any loose parts from falling out of projector." Warning: Lamp compartment is - Optoma HD33 | User's Manual - Page 48
. 3 7. Pull out the lamp module. 4 To replace the lamp module, reverse the previous steps. 8. Turn on the projector and do "Lamp Reset" after the lamp module is replaced. Lamp Reset: (i)Press "Menu" -> (ii)Select "System" -> (iii)Select "Lamp Settings" ->(iv)Select "Lamp Reset" -> (v)Select "Yes - Optoma HD33 | User's Manual - Page 49
Appendices Compatibility Modes ™™ Computer Compatibility for PC Signal NTSC PAL/SECAM VGA SVGA XGA HD720 WXGA WXGA-800 SXGA SXGA+ UXGA HD1080 WUXGA Resolution 720 x 400 720 x 400 720 x 576 - Optoma HD33 | User's Manual - Page 50
Resolution 1920 x 1080i 1920 x 1080i 1920 x 1080p 1920 x 1080p 1920 x 1080p 1280 x 720 1280 x 720p 1280 x 720p Digital O O O O O O O O O O O Analog O O O O O O O O O O O ™™ Computer Compatibility for MAC Resolution 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1024 x - Optoma HD33 | User's Manual - Page 51
Video Compatibility Input Resolution HDMI 1.4a 3D Input HDMI 1.3 3D Content 2D Input (include HDMI/VGA port) 2D Input (include HDMI/VGA/ Component/ Composite port) 1280 x 720p @ 50Hz 1280 x 720p @ 60Hz 1280 x 720p @ 50Hz 1280 x 720p @ 60Hz 1920 x 1080i @ 50 Hz 1920 x 1080i @ 60 Hz 1920 x 1080p - Optoma HD33 | User's Manual - Page 52
Appendices RS232 Commands and Protocol Function List RS232 Pin Assignments 1 3 5 6 8 Pin no. 1 2 3 4 5 6 7 8 9 Name NC RXD TXD NC GND NC RTS CTS NC I/O (From Projector Side) __ IN OUT __ Signal Ground __ __ __ __ English 52 - Optoma HD33 | User's Manual - Page 53
Appendices RS232 Protocol Function List Optoma Data and HT Projectors HD33 Baud Rate Data Bits Parity Optoma Data and HT Projectors Stop Bits BDFaautaldoBRwitasteControl PSUatorpitAyBRitsT16550 FIFO Flow Control UPARroT1j6e5c5t0oFrIFROeturn (Pass): P PrPojreoctojer Rcettourrn (RPaesst)u: Prn ( - Optoma HD33 | User's Manual - Page 54
Warming up Cooling Down Out of Range Lamp Fail Thermal Switch Error Fan Lock Over Temperature Lamp Hours Running Out READ/Return Information from projector Information a = Power State b = Lamp Hour c = Input Source Commands d = Firmware Version e = Display mode Model Name RS232 Version - Optoma HD33 | User's Manual - Page 55
Appendices ~ Lead Code X X Projector ID Contrast Format Color Temperature Projection Mode X 4:3/16:9/LBX/Native/Auto23 5/SuperWide Warm/Medium/Cold Front-Desktop RearDesktop Front-Ceiling Rear-Ceiling X Command ID Remote Control RS232 Commands for HD33 Remote Up/Page + Left/Source Enter ( - Optoma HD33 | User's Manual - Page 56
Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attached a mount to the projector met the following specifications: `` Screw type: M4*3 `` Maximum screw length: 10mm `` Minimum screw length: 7.5mm Warning: 1. If you buy a ceiling mount - Optoma HD33 | User's Manual - Page 57
service or support please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com 888-289-6786 510-897-8601 [email protected] Canada 2420 Meadowpine Blvd., Suite #105 Mississauga, ON, L5N 6S2, Canada www.optoma.ca 888-289-6786 510-897-8601 services@optoma - Optoma HD33 | User's Manual - Page 58
+49 (0) 211 506 6670 +49 (0) 211 506 66799 [email protected] +47 32 98 89 90 +47 32 98 89 99 [email protected] +82+2+34430004 +82+2+34430005 [email protected] www.os-worldwide.com +886-2-2218-2360 +886-2-2218-2313 [email protected] asia.optoma.com +852-2396-8968 +852-2370-1222 www - Optoma HD33 | User's Manual - Page 59
by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation Conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause - Optoma HD33 | User's Manual - Page 60
108/EC (including amendments) yy Low Voltage Directive 2006/95/EC yy R & TTE Directive 1999/5/EC (if product has RF function) Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
 |
 |
English
1
Table of Contents
Table of Contents
........................
1
Usage Notice
...............................
2
Safety Information
.......................................
2
Precautions
.................................................
3
Eye Safety Warnings
...................................
6
Introduction
.................................
7
Package Overview
......................................
7
Product Overview
........................................
8
Main Unit
..........................................................
8
Connection Ports
.............................................
9
Remote Control
..............................................
10
Installation
.................................
11
Connecting the Projector
...........................
11
Connect to Computer/Notebook
................
11
Connect to Video
.......................................
12
Connect to 3D Video Devices
...................
13
Using the 3D glasses
................................
15
Powering On/Off the Projector
..................
16
Powering On the Projector
.............................
16
Powering Off the Projector
.............................
17
Warning Indicator
...........................................
17
Adjusting the Projected Image
..................
18
Adjusting the Projector’s Height
.....................
18
Adjusting the Projector’s Zoom / Focus
.........
18
Adjusting Projection Image Size
....................
19
User Controls
............................
20
Remote Control
.........................................
20
On-screen Display Menus
.........................
22
How to operate
..............................................
22
Menu Tree
.................................................
23
IMAGE
...........................................................
25
IMAGE | Advanced
........................................
27
IMAGE | Advanced | PureEngine
...................
28
IMAGE | Advanced | Color Settings
...............
29
DISPLAY
........................................................
31
DISPLAY | 3D
................................................
33
SYSTEM
........................................................
35
SYSTEM | Lamp Settings
..............................
37
SETUP
...........................................................
38
SETUP | Signal -RGB Source
........................
40
SETUP | Signal -Video Source
......................
41
Appendices
................................
42
Troubleshooting
.........................................
42
Image Problems
.............................................
42
Other Problems
..............................................
44
Remote Control Problems
.............................
44
LED Lighting Messages
.................................
45
On Screen Messages
....................................
46
Replacing the Lamp
..................................
47
Compatibility Modes
..................................
49
RS232 Commands and Protocol Function
List
.............................................................
52
RS232 Pin Assignments
................................
52
RS232 Protocol Function List
........................
53
Ceiling Mount Installation
..........................
56
Optoma Global Offices
..............................
57
Regulation & Safety Notices
......................
59
FCC Notice
....................................................
59
Declaration of Conformity for EU countries ...60