Optoma HD39Darbee HD39Darbee User Manual - Page 19

USING THE PROJECTOR, Powering on / off the projector

Get Optoma HD39Darbee PDF manuals and user guides View all Optoma HD39Darbee manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

USING THE PROJECTOR Powering on / off the projector or RG2 ON OFF User1 User2 Contrast Brightness User3 Mode Aspect ratio Keystone Mute DB 3D Sleep Timer Volume Source R ON e-sync OFF Menu User1 User2 Brightness Contrast User3 Mode Aspect ratio Keystone Mute DB 3D Sleep Timer Volume Volume Source Re-sync HDMI1 HDMI2 Menu Volume HDMI1 HDMI2 VGA1 VGA2 Video YPbPr VGA1 VGA2 Video YPbPr Lens cap (*) Powering on 1. Remove the len's cap(*). 2. Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will turn red. 3. Turn on the projector by pressing the " " either on the projector keypad or the remote control. 4. A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing green or flashing blue. Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection orientation, and other settings. Powering off 1. Turn off the projector by pressing the " " either on the projector keypad or the remote control. 2. The following message will be displayed: Power Off Power Off? Press power key again. 3. Press the " " again to confirm, otherwise the message will disappear after a period of time (by default after 10 seconds). When you press the " " button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will flash green or flash blue. When the On/Standby LED turns solid red, this indicates the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode, simply press the " " button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure. English 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
English
19
USING THE PROJECTOR
Powering on / off the projector
Lens cap (*)
ON
OFF
Menu
VGA1
HDMI1
User2
Contrast
Aspect ratio
DB
Volume
Source
Re-sync
User1
Brightness
Keystone
Mute
User3
Mode
3D
Sleep Timer
Volume
HDMI2
VGA2
Video
YPbPr
ON
OFF
User2
Contrast
User1
Brightness
User3
Mode
or
Powering on
1.
Remove the len’s cap(*).
2.
Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will
turn red.
3.
Turn on the projector by pressing the "
" either on the projector keypad or the remote control.
4.
A start up screen will display in approximately 10 seconds and the On/Standby LED will be flashing
green or flashing blue.
Note°
The first time the projector is turned on, you will be prompted to select the preferred language, projection
orientation, and other settings.
Powering off
1.
Turn off the projector by pressing the "
" either on the projector keypad or the remote control.
2.
The following message will be displayed:
Power Off
Power Off?
Press power key again.
3.
Press the "
" again to confirm, otherwise the message will disappear after a period of time (by default
after 10 seconds). When you press the "
" button for the second time, the projector will shut down.
4.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
Standby LED will flash green or flash blue. When the On/Standby LED turns solid red, this indicates
the projector has entered standby mode. If you wish to turn the projector back on, you must wait until
the cooling cycle has finished and the projector has entered standby mode. When the projector is in
standby mode, simply press the "
" button again to turn on the projector.
5.
Disconnect the power lead from the electrical outlet and the projector.
Note°
It is not recommended that the projector is turned on immediately, right after a power off procedure.