Optoma HD8300 User's Manual - Page 42

English, Auto Power Off, Signal, Reset, Black Level: Allow user adjust Black Level when inputting S - manual

Get Optoma HD8300 PDF manuals and user guides View all Optoma HD8300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

User Controls NOTE  "Signal" is not supported when the input source is HDMI. NOTE  "IRE" is only supported on NTSC signal. Auto Power Off Set the interval of power-off of the system, if there is no signal input. (In minutes). Signal For RGB/Component Source  Frequency: Change the display data frequency to match the frequency of your computer's graphic card. Use this function only if the image appears to flicker vertically.  Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it.  H Position: Adjust the image horizontal position.  V Position: Adjust the image vertical position.  Automatic: Automatically selects the signal. If you use this function, the Frequency and Phase items are grayed out, and if Signal is not automatic, the Frequency and Phase items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again. For Video Source:  White Level: Allow user adjust White Level when inputting SVideo or Video/CVBS signals.  Black Level: Allow user adjust Black Level when inputting SVideo or Video/CVBS signals.  Saturation: Adjust a video image from black and white to fully saturated color. Press the ◄ to decrease the amount of color in the image. Press the ► to increase the amount of color in the image.  Hue: Adjust the color balance of red and green. Press the ◄ to increase the amount of green in the image. Press the ► to increase the amount of red in the image.  IRE: Adjust measurement of composite video signals. Reset Return the adjustments and settings to factory default values.  Current: Reset current signal's settings to factory default values.  All: Return the settings for all menus to factory default values. English 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
English
42
User Controls
“Signal” is not
supported when
the input source is
HDMI.
Auto Power Off
Set the interval of power-off of the system, if there is no signal
input. (In minutes).
Signal
For RGB/Component Source
Frequency: Change the display data frequency to match the
frequency of your computer’s graphic card. Use this function
only if the image appears to flicker vertically.
Phase: Synchronize the signal timing of the display with the
graphic card. If the image appears to be unstable or flickers,
use this function to correct it.
H Position: Adjust the image horizontal position.
V Position: Adjust the image vertical position.
Automatic: Automatically selects the signal. If you use this
function, the Frequency and Phase items are grayed out, and
if Signal is not automatic, the Frequency and Phase items will
appear for user to manually tune and saved in settings after
that for next time projector turns off and on again.
For Video Source:
White Level: Allow user adjust White Level when inputting
SVideo or Video/CVBS signals.
Black Level: Allow user adjust Black Level when inputting S-
Video or Video/CVBS signals.
Saturation: Adjust a video image from black and white to fully
saturated color. Press the ◄ to decrease the amount of color
in the image. Press the ► to increase the amount of color in
the image.
Hue: Adjust the color balance of red and green. Press the ◄
to increase the amount of green in the image. Press the ► to
increase the amount of red in the image.
IRE: Adjust measurement of composite video signals.
Reset
Return the adjustments and settings to factory default values.
Current: Reset current signal’s settings to factory default
values.
All: Return the settings for all menus to factory default values.
N
OTE
“IRE” is only sup-
ported on NTSC
signal.
N
OTE