Optoma Pico PK301 User's Manual - Page 7

Roubleshooting, Ompatibility, Ource, Omposite, Omponent - troubleshooting

Page 7 highlights

How to use the menu - Source: Composite AV, VGA, Component, HDMI Input signal source F Composite, HDMI or Component source F VGA source Only for VGA input source. F F Bright mode: Full LED power. Movie mode: Enhanced Color, Mid-Brightness. STD mode: Standard LED power. ECO mode: Economy LED power. F Front Desktop. Rear Desktop. F Front Inverted. Rear Inverted. 4x3 aspect ratio. 16x9 aspect ratio. Auto aspect ratio. Contrast: adjust contrast H. Position: adjust the horizontal position. V. Position: adjust the vertical position. Phase: change the display data frequency to match the frequency of your computer's graphic card. Use this function only if the image appears to flicker vertically. Frequency: synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it. Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image Problems No image appears on-screen • Ensure the cables/charger/ battery are correctly and securely connected. • Ensure the pins of connectors are not crooked or broken. • Make sure the projector is switched on. Image is out of focus • Adjust the Focus Dial. • Make sure the projection screen is between the required distance 9.6 to 126.6 inches (0.245 to 3.215 meters) from the projector. See page 5. Image is too small or too large • Move the projector closer to or further from the screen. Image is reversed • Select "Source --> Settings--> System Setup --> Projection" from the OSD and adjust the projection direction. Audio Problems No sound • Press the VOLUME + button. (See page 3.) Battery Problems Battery capacity is low • Remove the battery and clean the connectors. • The battery is worn out and needs to be replaced. See page 3. • The battery may not charge right away after the projector is turned off due to the high temperature emitted by the projector. Message LED (Red) Operation Battery Charging Charge Complete LED Indicator •  : Off / : Green / : Red Message Reminders • Out of range • High battery consumption Please charge the battery. (See page 3) or Compatibility Mode Timing Table Mode Resolution V-Sync (Hz) 640x480 60 800x600 60 VGA 1024x768 60 1280x720 60 1280x800 60 480i* / 480P 60 Composite* 576i* / 576P 50 Component HDMI 720P 50 / 60 1080i 50 / 60 Multimedia Format: Video File Video Format Format Max Res. AVI, MOV, MP4, H.264 720X480 30fps 3GP or 720x576 AVI MPEG4 25fps AVI Xvid AVI MJPEG 640X480 30fps Profile Baseline Simple Profile Baseline Baseline 1. Video format does not support content with B-Frame function. 2. Please use Arcsoft MediaConverter to convert video and PowerPoint files. Multimedia Format: Photo File Format File Extension JPG JPEG *.jpg, *.jpeg, *.bmp BMP Multimedia Format: Audio File Format AAC, MP3, PCM, ADPCM, WMA, OGG 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7

7
If you experience a problem with your
projector, please refer to the following
information. If a problem persists, please
contact your local reseller or service
center.
Image Problems
No image appears on-screen
Ensure the cables/charger/
battery are correctly and securely
connected.
Ensure the pins of connectors are
not crooked or broken.
Make sure the projector is
switched on.
Image is out of focus
Adjust the Focus Dial.
Make sure the projection screen
is between the required distance
9.6 to 126.6 inches (0.245 to 3.215
meters) from the projector. See
page 5.
Image is too small or too large
Move the projector closer to or
further from the screen.
Image is reversed
Select “Source --> Settings-->
System Setup --> Projection” from
the OSD and adjust the projection
direction.
Audio Problems
No sound
Press the VOLUME + button. (See
page 3.)
T
ROUBLESHOOTING
Battery Problems
Battery capacity is low
Remove the battery and clean the
connectors.
The battery is worn out and needs
to be replaced. See page 3.
The battery may not charge right
away after the projector is turned
off due to the high temperature
emitted by the projector.
Message
LED (Red)
Operation
Battery Charging
Charge Complete
LED Indicator
: Off /
: Green /
: Red
Message Reminders
• Out of range
• High battery consumption
Please charge the battery.
(See page 3)
C
OMPATIBILITY
M
ODE
H
OW
TO
U
SE
THE
M
ENU
- S
OURCE
: C
OMPOSITE
AV, VGA, C
OMPONENT
, HDMI
or
Timing Table
Mode
Resolution
V-Sync
(Hz)
VGA
640x480
60
800x600
60
1024x768
60
1280x720
60
1280x800
60
Composite*
Component
HDMI
480i* / 480P
60
576i* / 576P
50
720P
50 / 60
1080i
50 / 60
Multimedia Format: Video
File
Format
Video
Format
Max Res.
Profile
AVI,
MOV,
MP4,
3GP
H.264
720X480 30fps
or 720x576
25fps
Baseline
AVI
MPEG4
Simple
Profile
AVI
Xvid
Baseline
AVI
MJPEG
640X480 30fps
Baseline
<Note>
1. Video format does not support content
with B-Frame function.
2. Please use Arcsoft MediaConverter to
convert video and PowerPoint files.
Multimedia Format: Photo
File Format
File Extension
JPG
JPEG
BMP
*.jpg, *.jpeg, *.bmp
Multimedia Format: Audio
File Format
AAC, MP3, PCM, ADPCM, WMA, OGG
Input signal source
F
Bright mode: Full LED power.
Movie mode:
Enhanced Color,
Mid-Brightness.
STD mode: Standard LED power.
ECO mode:
Economy LED
power.
F
Front Desktop.
F
Rear Desktop.
F
Front Inverted.
F
Rear Inverted.
4x3 aspect ratio.
16x9 aspect ratio.
Auto aspect ratio.
Contrast: adjust contrast
H. Position: adjust the horizontal
position.
V. Position: adjust the vertical
position.
Phase: change the display data
frequency to match the frequency
of your computer’s graphic card.
Use this function only if the image
appears to flicker vertically.
Frequency: synchronize the signal
timing of the display with the
graphic card. If the image appears
to be unstable or flickers, use this
function to correct it.
Composite, HDMI or
Component source
VGA source
F
<Note>
Only for VGA input source.