Optoma X312 Manual - Page 14

Powering off the projector, Warning Indicator, ON/STANDBY LED will flash

Get Optoma X312 PDF manuals and user guides View all Optoma X312 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installation Powering off the projector 1. Press the " " button on the remote control or on the control panel to turn off the projector. The following message will be displayed on the screen. Press the " " button again to confirm otherwise the message will disappear after 15 seconds. The projector will shut down when the " " button is pressed for the second time. 2. The fans will continue to operate for 10 seconds and the ON/STANDBY LED will flash blue. During this period, the projector cannot be turned back on and the projector should not be unplugged. Once the cooling cycle is complete, the ON/STANDBY LED will turn to solid red (standby mode). At this point, the projector can be turned back on by pushing the " " button. 3. Disconnect the power cord from the electrical outlet and the projector. 4. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the warning indicators (see below) come on, the projector will automatically shutdown:  Contact the  "LAMP" LED indicator is lit red and if "On/Standby" indicator nearest service center if the projector displays these symptoms. See pages 63-64 for more flashes amber.  "TEMP" LED indicator is lit red and if "On/Standby" indicator flashes amber. This indicates the projector has overheated. Under normal conditions, the projector can be switched back on. information.  "TEMP" LED indicator flashes red and if "On/Standby" indicator flashes amber. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up again, please contact your nearest service center for assistance. English 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
14
English
Installation
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
63-64 for more
information.
Powering off the projector
1. Press the “
” button on the remote control or on the
control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “
” button again to confirm otherwise the
message will disappear after 15 seconds. The projector will
shut down when the “
” button is pressed for the second
time.
2. The fans will continue to operate for 10 seconds and the
ON/STANDBY LED will flash
blue. During this period,
the projector cannot be turned back on and the projector
should not be unplugged.
Once the cooling cycle is complete, the ON/STANDBY
LED will turn to solid red (standby mode). At this point, the
projector can be turned back on by pushing the “
” button.
3. Disconnect the power cord from the electrical outlet and the
projector.
4. Do not turn on the projector immediately following a power
off procedure.
Warning Indicator
When the warning indicators (see below) come on, the
projector will automatically shutdown:
“LAMP” LED indicator is lit red and if “On/Standby” indicator
flashes amber.
“TEMP” LED indicator is lit red and if “On/Standby”
indicator flashes amber. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
“TEMP” LED indicator flashes red and if “On/Standby”
indicator flashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.