Optoma ZH510T-B ZH510T User Manual - Page 35

Remote Setting, HDBaseT Control, PIP-PBP Module, Information Hide, Information

Get Optoma ZH510T-B PDF manuals and user guides View all Optoma ZH510T-B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

USER CONTROLS Note: Password default value is "000000" (first time). Always keep the password in your files. If the password is forgotten or lost, please contact your local authorized service center. Remote Setting  IR function: When this function is "Off", the projector cannot be operated by the remote control.  Remote code: 00~99, default code (common code): 00 HDBaseT Control • The projector will automatically detect the signal from HDBaseT transmitter supplied. Choose "HDBaseT" to activate Direct Power mode. • When HDBaseT control is ON, 12v trigger output signal will always be ON, even if the projector is on Standby mode. PIP-PBP Module • Version: Show PIP-PBP module software version. • Reset: Reset the PIP-PBP module. • USB Upgrade: Upgrade the PIP-PBP module software. • HDMI EQ: Set PIP-PBP module HDMI port EQ value. Information Hide • On: Choose "On" to hide the info message. • Off: Choose "Off" to show the "info" message. Information Display the projector information for model name, SNID, source, resolution, software version, aspect ratio, SSI Hours, IP Address and Network Status on the screen. Signal Power On & HDBaseT Standby To access Signal Power On and HDBaseT Standby menu -- with projector on press the following buttons (in order): Power > Up >Down> Menu. Signal Power On • On: Choose "On" to enable Signal Power On. • Off: Choose "Off" to disable Signal Power On. HDBaseT Standby • On: Choose "On" to enable HDBaseT Standby. • Off: Choose "Off" to disable HDBaseT Standby. English 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
English 35
USER CONTROLS
Note:
Password default value is “000000” (first time).
Always keep the password in your files. If the password is forgotten or lost, please contact your local autho
-
rized service center.
Remote Setting
IR function: When this function is “Off”, the projector cannot be operated by the remote control.
Remote code: 00~99, default code (common code): 00
HDBaseT Control
The projector will automatically detect the signal from HDBaseT transmitter supplied. Choose “HDBaseT” to
activate Direct Power mode.
PIP-PBP Module
Version: Show PIP-PBP module software version.
•
Reset: Reset the PIP-PBP module.
•
USB Upgrade: Upgrade the PIP-PBP module software.
•
HDMI EQ: Set PIP-PBP module HDMI port EQ value.
•
Information Hide
On: Choose “On” to hide the info message.
•
Off: Choose “Off” to show the “info” message.
•
Information
Display the projector information for model name, SNID, source, resolution, software version, aspect ratio, SSI
Hours, IP Address and Network Status on the screen.
When HDBaseT control is ON, 12v trigger output signal will always be ON, even if the
projector is on Standby mode.
•
•
Signal Power On & HDBaseT Standby
On: Choose “On” to enable Signal Power On.
•
Off: Choose “Off” to disable Signal Power On.
•
To access Signal Power On and HDBaseT Standby menu -- with projector on press the following buttons (in order):
Power > Up >Down>
Menu.
HDBaseT Standby
On: Choose “On” to enable HDBaseT Standby.
•
Off: Choose “Off” to disable HDBaseT Standby.
•
Signal Power On