Optoma ZU860 ZU860 User Manual - Page 19

Remote setup, Installing / replacing the batteries, Remote control ID setup, Hot Key

Get Optoma ZU860 PDF manuals and user guides View all Optoma ZU860 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

SETUP AND INSTALLATION Remote setup Installing / replacing the batteries Two AAA size batteries are supplied for the remote control. 1. Remove the battery cover on the back of the remote control. 2. Insert AAA batteries in the battery compartment as illustrated. 3. Replace back cover on remote control. Note: Replace only with the same or equivalent type batteries. CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. ‡‡ Do not mix batteries of different types. Different types of batteries have different characteristics. ‡‡ Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries. ‡‡ Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth. ‡‡ The batteries supplied with this product may have a shorter life expectancy due to storage conditions. ‡‡ If you will not be using the remote control for an extended period of time, remove the batteries. ‡‡ When you dispose of the batteries, you must obey the law in the relative area or country. Remote control ID setup The Infra-Red (IR) remote control supports individual addressing of projectors. The remote receiver on the projector can be set with a specific number from 00 to 99, and the projector only responds to the IR remote set to the same number. The default ID code of the IR remote is 00, allowing it to control all projectors within its effective range. Follow below methods to set up the ID code for the IR remote control: ID Code 01 02 03 ... 10 11 ... 98 99 Change method Press Hot Key for 3 seconds, and press 0 then 1 within 2 seconds. Press Hot Key for 3 seconds, and press 0 then 2 within 2 seconds. Press Hot Key for 3 seconds, and press 0 then 3 within 2 seconds. ... Press Hot Key for 3 seconds, and press 1 then 0 within 2 seconds. Press Hot Key for 3 seconds, and press 1 then 1 within 2 seconds. ... Press Hot Key for 3 seconds, and press 9 then 8 within 2 seconds. Press Hot Key for 3 seconds, and press 9 then 9 within 2 seconds. Customer code 0010 0011 0012 ... 0019 001A ... 0071 0072 To have the IR remote control return to default value 00 where all projectors can be controlled, press Hot Key for 3 seconds, and press 0 twice within 2 seconds. For more information on setting the remote receivers on the projector, see Projector ID from the setup menu on page 44. English 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
English
19
SETUP AND INSTALLATION
Remote setup
Installing / replacing the batteries
Two AAA size batteries are supplied for the remote control.
1.
Remove the battery cover on the back of the remote control.
2.
Insert AAA batteries in the battery compartment as illustrated.
3.
Replace back cover on remote control.
Note:
Replace only with the same or equivalent type batteries.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
±
Do not mix batteries of different types. Different types of batteries have different characteristics.
±
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or
cause chemical leakage in old batteries.
±
Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contact
with skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
±
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
±
If you will not be using the remote control for an extended period of time, remove the batteries.
±
When you dispose of the batteries, you must obey the law in the relative area or country.
Remote control ID setup
The Infra-Red (IR) remote control supports individual addressing of projectors. The remote receiver on the projector
can be set with a specific number from 00 to 99, and the projector only responds to the IR remote set to the same
number. The default ID code of the IR remote is 00, allowing it to control all projectors within its effective range.
Follow below methods to set up the ID code for the IR remote control:
ID Code
Change method
Customer code
01
Press
Hot Key
for 3 seconds, and press
0
then
1
within 2 seconds.
0010
02
Press
Hot Key
for 3 seconds, and press
0
then
2
within 2 seconds.
0011
03
Press
Hot Key
for 3 seconds, and press
0
then
3
within 2 seconds.
0012
...
...
...
10
Press
Hot Key
for 3 seconds, and press
1
then
0
within 2 seconds.
0019
11
Press
Hot Key
for 3 seconds, and press
1
then
1
within 2 seconds.
001A
...
...
...
98
Press
Hot Key
for 3 seconds, and press
9
then
8
within 2 seconds.
0071
99
Press
Hot Key
for 3 seconds, and press
9
then
9
within 2 seconds.
0072
To have the IR remote control return to default value 00 where all projectors can be controlled, press
Hot Key
for 3
seconds, and press
0
twice within 2 seconds.
For more information on setting the remote receivers on the projector, see
Projector ID
from the setup menu on
page 44.