Oregon Scientific BAR206S User Manual - Page 1

Oregon Scientific BAR206S Manual

Get Oregon Scientific BAR206S PDF manuals and user guides View all Oregon Scientific BAR206S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

QUICK START GUIDE OREGON SCIENTIFIC WEATHER COLLECTION B SET-UP WIRELESS SENSOR You will have one of the following Oregon Scientific products: 100 : EMR201A 400 : BAR206A 1 200 : RMR202A 500 : BAR208HGA 2 300 : RMR203HGA RAIN AND TEMPERATURE STATION: RGR202A A UNPACK Make sure that you have all of the parts of one of the three groups of products shown here before the installation of your Weather Collection product. WEATHER 100-400 WEATHER 500 1 Slide open battery door 2 Install the battery, matching polarity (+/-) C SET-UP MAIN UNIT 4 3 3 Assign a channel by sliding selection switch to the appropriate channel (1,2,3) location. If installing additional sensors, make sure you assign a different channel for each sensor. 4 Press the reset button * Before placing the sensor outdoors, please verify communication with the main unit by placing the sensor next to the base unit during this setup process. 1× Main Unit 1× THN132N 1× Main Unit 1× THGR122NR Temperature Sensor Temperature/ Humidity Sensor 1 2 RAIN AND TEMPERATURE STATION Time is synchronized. Receiving signal is strong. 3 Time is not synchronized. Receiving signal is weak. 1× Main Unit 1× THN132N Temperature Sensor 1× Rain Collector 1× Filter 3× Screws (Type C) 6× Washers 1 Install the required number of batteries in the battery compartment located on the back of each main unit. 2 There are two types of signals the main unit will receive: Temperature Signal After installing the batteries, the main unit will automatically search for the signal from the wireless sensor. Once a temperature reading is displayed on the LCD screen, communication is now established. 3 Atomic Clock Signal Atomic clock synchronization will automatically occur after installing the batteries. Reception takes 2-10 minutes. If the signal is weak, it can take up to 24 hours to retrieve a valid signal. * Please monitor atomic clock icon ( ) on the bottom part of the LCD display next to the time. This icon indicates the status of the clock reception signal.

  • 1
  • 2
UNPACK
Make sure that you have all of the parts of one of the three
groups of products shown here before the installation of your
Weather Collection product.
A
SET-UP WIRELESS SENSOR
B
SET-UP MAIN UNIT
C
WEATHER
THN132N
Temperature
Sensor
1×
RAIN AND
TEMPERATURE STATION
Rain Collector
1×
Screws (Type C)
3×
Washers
6×
Filter
1×
Main Unit
1×
QUICK START GUIDE
OREGON SCIENTIFIC WEATHER COLLECTION
Slide open battery door
1
Install the battery, matching polarity (+/-)
2
Assign a channel by sliding selection switch to the appropriate
channel (1,2,3) location. If installing additional sensors, make
sure you assign a different channel for each sensor.
Press the reset button
Before placing the sensor outdoors, please verify
communication with the main unit by placing the sensor next to
the base unit during this setup process.
3
4
Atomic Clock Signal
Atomic clock synchronization will automatically occur after
installing the batteries. Reception takes 2-10 minutes. If the
signal is weak, it can take up to 24 hours to retrieve a valid
signal.
Please monitor atomic clock icon (
) on the bottom part of the
LCD display next to the time. This icon indicates the status of
the clock reception signal.
3
WEATHER
THGR122NR
Temperature/
Humidity Sensor
1×
Main Unit
1×
Main Unit
1×
2
1
3
4
Install the required number of batteries in the battery
compartment located on the back of each main unit.
1
There are two types of signals the main unit will receive:
Temperature Signal
After installing the batteries, the main unit will automatically
search for the signal from the wireless sensor. Once a
temperature reading is displayed on the LCD screen,
communication is now established.
2
1
2
3
Time is synchronized.
Receiving signal is strong.
Time is not synchronized.
Receiving signal is weak.
: BAR206A
: BAR208HGA
RAIN AND TEMPERATURE STATION:
RGR202A
: EMR201A
: RMR202A
: RMR203HGA
You will have one of the following Oregon Scientific products:
100
200
300
500
100-400
400
500
*
*
THN132N
Temperature
Sensor
1×