Panamax M7500-PRO Datasheet - Page 2

MAX® 7500-PRO BACK PANEL FEATURES 1. 15A Main Circuit Breaker: Opens in the event that equipment plugged into the MAX 7500 draws too much current. When white is visible, the breaker has opened. Reduce the load and push to reset. 2. Filtered Regulated Outlets (BANKS 1 & 2): Four, Balanced Double L filtered outlets for low current analog audio components such as pre-amplifiers, receivers, VCR's and tape decks. 3. Isolated (Switched) Outlets (BANKS 3 & 4): Four outlets provide complete isolation for digital source components such as DVD players or display devices like plasma TVs or DLP projectors. These outlets are completely isolated from the rest of the system. 4. High Current Outlet Bank (BANK 5): Two delayed outlets designed for high current components such as amplifiers and powered subwoofers. The current available to connected equipment is not limited by the noise filtration components. 5. Isolated Outlets Circuit Breaker: Opens in the event that equipment connected to the Isolation Transformer Outlets exceeds 6 Amps current draw. When white is visible, the breaker has opened. Reduce the load and push to reset. 6. Universal Cable and Satellite TV Coax Jacks: Two pairs of F-Connectors optimized for Satellite TV, Cable TV, Antenna or Cable Modem signal line protection. Bi-directional 7. Settings Option: Two-position slide switch. Switch settings selects the use of the five switches to configure the outlets for delayed or always-on operation. Custom settings selects the stored configuration in non-volatile memory for the outlets trigger source and delays. 8. IEC Main Power Receptacle: Detachable power cord connects to this receptacle. 9. Ground Lug: Provides a common grounding point for equipment with separate ground leads 10. DC Trigger Input: 3.5mm (1/8") Mini-Plug jack. Connect to a remote trigger device that uses a DC voltage signal to initiate a startup/shutdown sequence. 11. DC Trigger Output: 3.5mm (1/8") Mini-Plug jack. The M7500Pro generates its own 12VDC trigger to control another device. MAX® 7500-PRO SPECIFICATIONS General Dimensions 17 in. W x 12.75 in. D x 3.5 in H, (4.1 in. Including feet) Weight...36 lbs. AC Power Line Voltage...120V, 60Hz Regulation Range 100V-135V Regulated Output 120V ± 2V Total Current Capacity...15 A Suppression Rating...330V Protection Modes L-N, L-G, N-G Initial Clamping Level...200V Energy Dissipation 2670 Joules Peak Impulse Current 162,000 Amps Catastrophic Surge Circuit Yes Thermal Fusing:...Yes Over-voltage shutoff 142 VAC ± 5 VAC Under-voltage shutoff 90 VAC ± 2 VAC EMI/RFI Noise Filtration Banks 1 - 4 100 db, 100 KHz - 2 MHz Bank 5, High Current Outlets 60 db, 100 KHz - 2 MHz USB Light Voltage...5VDC Current...100mA DC Trigger Input Jacks 3.5mm mono mini-plug Voltage and Polarity 3 - 24V DC, bidirectional Current Requirement 4.6 mA @3V, 58 mA @24V Design and specifications subject to change without notice due to product improvement. 12. Outlet Delay Switches: Two-position slide switches. Allows for the user to configure each bank for delayed turn-on/turn-off or always-on operation. 13. LAN: In/Out connections for Ethernet. 14. Telephone Jacks: 1 In & 2 Out connections for telephone line or pay-per-view line protection. 15. Lamp Receptacle: USB jack. The convenience lamp included with the M7500-Pro is to illuminate the rear panels of other components during setup. 16. Communications Interface: RS232 interface for custom configuration and/or home automation control. Contact Panamax for availability of alternate TCP/IP interface. DC Trigger Output Voltage...