Panasonic 58PF12UK Operating Instructions - Page 9

Connections - th manual

Get Panasonic 58PF12UK - TH - 58inch Plasma Panel PDF manuals and user guides
UPC - 037988242825
View all Panasonic 58PF12UK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connections When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 Speaker terminal (L) Speaker terminal (R) AC cord connection (see page 13) 2 - AC cord fixing 1 1 Plug the AC cord into the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper 2 which is attached to the unit. For TH-58PF12UK: Note: Clampers are not installed to this Make sure that the AC unit. Ensure there is sufficient slack cord is locked on both in the AC cord and firmly bind with the left and right sides. the supplied cable fixing band, etc. Close Open Unplug the AC cord Push until the hook clicks. Unplug the AC cord pressing the two knobs. 2. Pull off. 1. Keep the knob pressed. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. - Cable fixing band Secure any excess cables with band as required. Note: One fixing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. To tighten: To loosen: Push the catch Pull 1 2 Pull SLOT1 SLOT2 R AUDIO L PR/CR/R PB/CB/B Y/G COMPONENT/RGB IN SLOT3 AUDIO PC IN SERIAL Optional Terminal Board Insert Slot (covered) Dual HDMI Terminals (equivalent of Dual HDMI Terminal Board (TYFB10HMD)) (see page 12) COMPONENT/RGB IN and Audio IN Terminals (equivalent of BNC Component Video Terminal Board (TY-42TM6A)) (see page 12) From EXTERNAL monitor terminal on Computer (see page 10) From SERIAL Terminal on Computer (see page 11) Note: At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1
2
SERIAL
PC
IN
AUDIO
SLOT1
SLOT3
P
R
/C
R
/R
P
B
/C
B
/B
Y/G
AUDIO
R
L
COMPONENT/RGB IN
SLOT2
1
2
1
2
1
2
9
Connections
– Cable
fi
xing band
Secure any excess cables with band as required.
Note:
One
fi
xing band is supplied with this unit. In case of securing cables at two positions, please purchase it separately.
Speaker
terminal (R)
Speaker
terminal (L)
When connecting the speakers, be sure to use only the optional accessory speakers.
Refer to the speaker’s Installation Manual for details on speaker installation.
Speakers (Optional accessories)
Pass the attached cable
fi
xing band through the clip
as shown in the
fi
gure.
To secure cables connected to Terminals, wrap the cable
fi
xing band around them then
pass the pointed end through the locking block, as shown in the
fi
gure.
While ensuring there is suf
fi
cient slack in cables to minimize stress (especially
in the power cord),
fi
rmly bind all cables with the supplied
fi
xing band.
From SERIAL
Terminal on
Computer
(see page 11)
From EXTERNAL
monitor terminal
on Computer
(see page 10)
AC cord connection (see page 13)
Dual HDMI Terminals
(equivalent of Dual HDMI
Terminal Board (TY-
FB10HMD)) (see page 12)
To tighten:
To loosen:
Pull
Pull
Push the catch
Note:
At factory shipment, Terminal boards are installed in SLOT 2 and SLOT 3.
– AC cord
fi
xing
Optional Terminal
Board Insert Slot
(covered)
COMPONENT/RGB IN and Audio
IN Terminals (equivalent of BNC
Component Video Terminal Board
(TY-42TM6A)) (see page 12)
Note:
Make sure that the AC
cord is locked on both
the left and right sides.
Push until
the hook
clicks.
2.
Pull off.
1.
Keep the
knob
pressed.
Open
1
Plug the AC cord into
the display unit.
Plug the AC cord until it
clicks.
2
Fix the AC cord with the clamper
which is attached to the unit.
For TH-58PF12UK
:
Clampers are not installed to this
unit. Ensure there is suf
fi
cient slack
in the AC cord and
fi
rmly bind with
the supplied cable
fi
xing band, etc.
Unplug the AC cord
Unplug the AC cord
pressing the two
knobs.
Note:
When disconnecting the AC cord,
be absolutely sure to disconnect
the AC cord plug at the socket
outlet
fi
rst.
Close