Panasonic AW-RP150GJ AW-RP150 Controller AW-UE150 PRO PTZ Camera Brochure - Page 11

As of November, 2019 Image Transmission Setting (H.264): Image Transmission Setting (H.265): Frame Rate [60Hz] 5fps/15fps/30fps/60fps (UHD: 30fps, 60fps) [50Hz] 5fps/12.5fps/25fps/50fps (UHD: 25fps, 50fps) Max Bit Rate HD : 512kbps/768kbps/1024kbps/1536kbps/2048kbps/ 3072kbps/4096kbps/6144kbps/8192kbps/10240kbps/ 12288kbps/14336kbps/16384kbps/20480kbps/24576kbps/ 32768kbps/40960kbps/51200kbps/76800kbps UHD: 12800kbps/25600kbps/51700kbps/76800kbps Image Transmission Type: Unicast port (AUTO) Unicast port (MANUAL) Multicast port Frame Rate [60Hz] 30fps [50Hz] 25fps Max Bit Rate 8192kbps/12800kbps/25600kbps/51200kbps/76800kbps Audio Compression Type: AAC-LC, 48 kHz / 16 bit / 2ch Supported Protocol: IPv6 : TCP / IP, UDP / IP, HTTP, HTTPS, DNS, NTP, DHCPv6, RTP, MLD, ICMP, ARP, RTMP, RTMPS IPv4 : TCP / IP, UDP / IP, HTTP, HTTPS, RTSP, RTP / RTCP, DHCP, DNS, DDNS, NTP, UPnP, IGMP, ICMP, ARP, RTMP, RTMPS NDI support*12: NDI | HX Tally LED display color: red / green *1: Use may require a software version update. *2: 1 dB step increments can be set. *3: This cannot be configured when the format is 2160/29.97p, 2160/23.98p, 2160/24p, 2160/25p, 1080/29.97p, 1080/23.98p(59.94i), 1080/29.97PsF, 1080/23.98PsF, 1080/25p, 1080/25PsF. *4: Native output. *5: It denotes "1080/23.98p over 59.94i". *6: Use of an STP (shielded twisted pair) cable is recommended. *7: Category 6 or more is used when sending 4K images. *8: To ensure safety, the unit must be secured using the mount bracket supplied. *9: Quietness, stationary accuracy, etc., in high-speed mode may vary from normal mode. *10: Depending on the pan or tilt position, the camera may be reflected in the image. *11: Supported OS indicated are for browsers current as of October 2018. See "Service and Support / PASS" on the Panasonic website (https://pro-av.panasonic.net/en/) for the latest information on browser support. *12: Contact your local Panasonic vendor for further information. AW-RP150GJ Power Requirements: 12 V DC (10.8 V to 13.2 V) PoE+: IEEE802.3at standard: DC 42 V to 57 V (Camera Input) Current Consumption: 1.0 A (Connector Input) 0.6 A (PoE+ power supply) Ambient Operating Temperature: 0 °C to 40 °C (32 °F to 104 °F) Allowable Humidity: 20% to 90% (no condensation) Storage Temperature: -20 °C to 50 °C (-4 °F to 122 °F) Weight: Approx. 3.2 kg (7.05 lb) Dimensions (W x H x D): 342 mm x 178 mm x 245 mm (13-15/32 inches x 7 inches x 9-21/32 inches) (excluding protrusions) Connection IP/RS422 Supported Equipment: AW-UE150W/K, AW-HR140*1, AW-HE130W/K*1, AW-HN130W/K*1, AW-UE70W/K*1, AW-UN70W/K*1, AW-HE42W/K, AW-HE40 Series*1, AW-HN40HW/HK*1, AW-HE38HW/HK*1, AW-HN38HW/HK*1 Input: DC 12 V IN XLR 4‑pin 3G-SDI IN SMPTE292 / 75 Ω (BNC x 1) Supported formats: 1080/59.94p*2, 1080/50p*2, 1080/59.94i, 1080/50i, 1080/23.98p, 1080/25p, 1080/23.98PsF, 1080/25PsF Output: ACTIVE THRU OUT SMPTE292 / 75 Ω (BNC x 1) Input/ IP CONT Output: 100BASE‑TX PoE+ input Connection cable: LAN cable, max. 100 m (328 ft) • When connecting the unit via a switching hub: Straight cable or a cross cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended • When connecting the unit directly: Crossover cable (category 5 cable), STP (Shielded Twisted Pair) cable recommended SERIAL CONT RS‑422 (control signals for remote cameras), TALLY OUT (RJ‑45): Connecting cable: Straight cable (category 5e or better shielded cable), max. 1000 m (3280 ft) TALLY OUT: Open collector output (negative logic) Maximum voltage resistance DC 24 V, Maximum current 50 mA Input/ TALLY/ Output: GPIO 1 GPIO 2 LCD Display: SD Memory Card Slot : D‑sub 25‑pin, female, inch thread TALLY IN : 10 inputs (for receiving photocoupler signals) GPI : 6 inputs (for receiving photocoupler signals) GPIO : 5 inputs (for receiving photocoupler signals) or 5 outputs (open collector outputs, negative logic) • Input/output switched with menu settings D‑sub 25‑pin, female, inch thread GPI : 10 inputs (for receiving photocoupler signals) GPIO : 10 inputs (for receiving photocoupler signals) or 10 outputs (open collector outputs, negative logic) • Input/output switched with menu settings Reserve connectors: 2 connectors (For future expansion feature) 7-inch Touch Panel GUI Monitor (WVGA (800×480) ) SDHC / SDXC Memory Card Slot x 1 No. of Connectable Cameras: 200 (IP), 5 (RS422) No. of Camera Selection Buttons: 10 No. of Camera Groups: 20 (10 units per 1 group) Preset Memory: No. of memory presets 100 Tracing Memory: No. of cameras Cam1 to Cam10 Recording time, no. of memory Maximum 5 min. total per camera, maximum of 10 settings per camera settings No. of User Assignable Buttons: 6 + up to 10 on the LCD menu Pan / Tilt Speed Adjustment: 7 levels Tally LED Display Color: green / red *1: Use may require a software version update. *2: Level-A support only. 11