Panasonic MCCG973 MCCG973 User Guide - Page 40

Removing Belt, Turn Power Nozzle Over.

Get Panasonic MCCG973 - CANISTER VAC - MULTI LANGUAGE PDF manuals and user guides
UPC - 037988690862
View all Panasonic MCCG973 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Removing Belt Tab Languette Pestaña SCRINESWEDRRTIVER TAOTSAERPRAORWATE ➢ Disconnect vacuum cleaner from electrical outlet. ➢ Frequently check and remove hair, string and lint buildup in the POWER NOZZLE brush and brush support areas. ➢ If buildup becomes excessive, disconnect POWER NOZZLE from wand and follow the steps below. ➢ Remove light cover and light bulb as shown under "REPLACING HEADLIGHT BULB". ➢ Unscrew the two (2) POWER NOZZLE cover screws . ➢ Turn POWER NOZZLE over. ➢ To remove cover, insert screwdriver at cover tabs on both sides and twist to release tabs. ➢ Turn POWER NOZZLE right side up. ➢ Press handle release pedal and lower the swivel. Base Base Base End Cap Bouchon BasTeapa del extremo ➢ Tilt cover forward from back until front snaps free. ➢ Carefully insert and twist screwdriver at each brush support to free brush from base. ➢ Remove worn belt. ➢ See AGITATOR ASSEMBLY for picture of complete brush assembly. - 40 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
INSERT
SCREWDRIVER
AT ARROW
TO SEPARATE
Tab
Languette
Pesta
ñ
a
Removing Belt
Base
Base
Base
Base
End Cap
Bouchon
Tapa del
extremo
➢
Disconnect vacuum cleaner from
electrical outlet.
➢
Frequently check and remove hair,
string and lint buildup in the
POWER NOZZLE brush and brush
support areas.
➢
If buildup becomes excessive,
disconnect POWER NOZZLE from
wand and follow the steps below.
➢
Remove light cover and light bulb
as shown under “REPLACING
HEADLIGHT BULB”.
➢
Unscrew the two (2) POWER
NOZZLE cover screws
.
➢
Turn POWER NOZZLE over.
➢
To remove cover, insert screwdriver
at cover tabs on both sides and
twist to release tabs.
➢
Turn POWER NOZZLE right side up.
➢
Press handle release pedal and
lower the swivel.
➢
Tilt cover forward from back until
front snaps free.
➢
Carefully insert and twist
screwdriver at each brush support
to free brush from base.
➢
Remove worn belt.
➢
See AGITATOR ASSEMBLY for
picture of complete brush
assembly.
- 40 -