Panasonic TH-43LFE8U Professional Display for Simple Entry-Level Digital Signage - Page 78

Page 78 highlights

Data Cloning Menu settings and adjusted values set on a single display can be copied to multiple displays using a USB memory. Ŷ Data that can be copied Settings and set values of [Picture], [Sound], [Setup], [Position] and [Options] menus Ɣ The following data cannot be copied. Setting is required for each display. Date and time Setting for [Network settings] - [LAN setup] Display ID in [Options] - [Display ID] Ŷ Supported device Ɣ Commercially available USB memory devices are supported. (Those with security functions are not supported.) Ɣ USB memory devices other than those formatted in FAT16 or FAT32 cannot be used. Ɣ Up to 32 GB of USB memory in size are supported. Ɣ Only single partition configuration is supported. Note Ɣ If the inch size for display differs, the cloning function does not operate. Use the common inch size. Ɣ The remote control is used to display [USB data cloning] menu. Unit buttons cannot be used to display the menu. Ɣ Set the input to something other than [USB], and perform the data cloning. Copying the display data to the USB memory 1 Insert the USB memory device to the USB terminal on the side edge of the display. USB terminal USB memory Note Ɣ Depending on the type of a USB memory device, it may come in contact with the periphery such as a back cover, and cannot be attached. Use a commercially sold extension cable, or use a small type of a USB memory device connectable to this unit. Ɣ If the USB memory containing the data for cloning is connected in power-on state, the [Select Copy Type] message in step 5 is displayed. Select >'LVSOD\ĺ86%0HPRU\@$OVRLIWKHGDWDFRS\LV performed, the saved data is overwritten. Ɣ Failure to save in or read from the USB memory displays an error message. 2 Display [Setup] menu pressing . 3 Select [OSD Language] with and press for over 3 seconds. The following display appears. Options Display serial number Software licenses USB data cloning Shipping 4 Select [USB data cloning] with and press . 5 6HOHFW>'LVSOD\ĺ86%0HPRU\@ZLWK and press . Select Copy Type 'LVSOD\ ĺ86%0HPRU\ 86%0HPRU\ĺ'LVSOD\ 78 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
English
78
Data Cloning
Menu settings and adjusted values set on a single
display can be copied to multiple displays using a USB
memory.
Ŷ
Data that can be copied
Settings and set values of [Picture], [Sound], [Setup],
[Position] and [Options] menus
Ɣ
The following data cannot be copied. Setting is
required for each display.
Date and time
Setting for [Network settings] - [LAN setup]
Display ID in [Options] - [Display ID]
Ŷ
Supported device
Ɣ
Commercially available USB memory devices are
supported. (Those with security functions are not
supported.)
Ɣ
USB memory devices other than those formatted in
FAT16 or FAT32 cannot be used.
Ɣ
Up to 32 GB of USB memory in size are supported.
Ɣ
Only single partition configuration is supported.
Note
Ɣ
If the inch size for display differs, the cloning
function does not operate. Use the common inch
size.
Ɣ
The remote control is used to display [USB data
cloning] menu. Unit buttons cannot be used to
display the menu.
Ɣ
Set the input to something other than [USB], and
perform the data cloning.
Copying the display data to the USB
memory
1
Insert the USB memory device to the
USB terminal on the side edge of the
display.
USB
memory
USB
terminal
Note
Ɣ
Depending on the type of a USB memory device,
it may come in contact with the periphery such
as a back cover, and cannot be attached. Use a
commercially sold extension cable, or use a small
type of a USB memory device connectable to this
unit.
Ɣ
If the USB memory containing the data for cloning
is connected in power-on state, the [Select Copy
Type] message in step 5 is displayed. Select
>'LVSOD\ ĺ 86% 0HPRU\@² $OVR± LI WKH GDWD FRS\ LV
performed, the saved data is overwritten.
Ɣ
Failure to save in or read from the USB memory
displays an error message.
2
Display [Setup] menu pressing
<SETUP>.
3
Select [OSD Language] with
and
press <ENTER> for over 3 seconds.
The following display appears.
Options
Display serial number
Shipping
USB data cloning
Software licenses
4
Select [USB data cloning] with
and press <ENTER>.
5
6HOHFW >'LVSOD\ ĺ 86% 0HPRU\@ ZLWK
and press <ENTER>.
Select Copy Type
'LVSOD\ ĺ 86% 0HPRU\
86% 0HPRU\ ĺ 'LVSOD\