Pfaff hobbylock 788 Owner's Manual - Page 13

Pfaff hobbylock 788 Manual

Get Pfaff hobbylock 788 PDF manuals and user guides View all Pfaff hobbylock 788 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Needle threader is Lower the sewing foot by means of lif ting lever 16. Turn the hand wheel until right looper 31 is positioned right of the needle (see top of page 18). Place the thread in slot A of needle threader 42 and tauten it a little, holding the needle threader a little turned to the front. With the needle located between the two guide lugs B move the needle threader slowly downwards at the rear side of the needle until small hook C engages in the needle eye. Hold the thread taut and place it in hook D; it will then automatically be placed in hook C, too. Pull the needle threader to the rear, out of the needle eye, and the thread will be pulled through the eye. Pull the thread completey through the needle eye. Thread spool change on threaded machine Cut the threads close to the thread spool. Place new thread spools on spool holders 1 7. Tie the threads still in the machine and the new threads to-gether. Pull the needle threads out of the needles. Now pull at the thread ends until the knots are about 1 5 cm past the last thread guide before the needles. Cut the knots off and pull the threads through the respective needle eyes. The looper threads can be pulled until past the looper eyes without interruption. Pull about 10 cm of thread through the looper eye. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
is
Needle
threader
Lower
the
sewing
foot
by
means
of
lif
ting
lever
16.
Turn
the
hand
wheel
until
right
looper
31
is
positioned
right
of
the
needle
(see
top
of
page
18).
Place
the
thread
in
slot
A
of
needle
threader
42
and
tauten
it
a
little,
holding
the
needle
threader
a
little
turned
to
the
front.
With
the
needle
located
between
the
two
guide
lugs
B
move
the
needle
threader
slowly
downwards
at
the
rear
side
of
the
needle
until
small
hook
C
engages
in
the
needle
eye.
Hold
the
thread
taut
and place
it
in
hook
D;
it
will
then
automatically
be
placed
in
hook
C,
too.
Pull
the
needle
threader
to
the
rear,
out
of
the
needle
eye,
and
the
thread
will
be
pulled
through
the
eye.
Pull
the
thread
completey
through
the
needle
eye.
Thread
spool
change
on
threaded
machine
Cut
the
threads
close
to
the
thread
spool.
Place new
thread
spools
on
spool
holders
1
7.
Tie
the
threads
still
in
the
machine
and
the
new
threads to-gether.
Pull
the
needle
threads
out
of
the
needles.
Now
pull
at
the
thread
ends
until
the
knots
are
about
1
5
cm
past
the
last
thread
guide
before
the
needles.
Cut
the
knots
off
and
pull
the threads
through
the
respective
needle
eyes.
The
looper
threads
can
be
pulled
until
past
the
looper
eyes
without
interruption.
Pull
about
10
cm
of
thread
through
the
looper
eye.
11