Philips 23PF9976I Quick start guide (English) - Page 2

B LCD TV This LCD television has a set of controls located on the side of the cabinet for use when the remote control is not needed. 1 After you have connected the power cord to the TV and plugged the cord into a wall outlet, press the POWER button on the front of the TV cabinet to turn the TV ON. 2 Press the VOLUME + button to increase the sound level or the VOLUME - button to lower the sound level. Pressing both buttons at the same time will display the onscreen menu. After you are in the menu, use these buttons to make adjustments or selections. 3 Press the CHANNEL + or - button to select TV channels. Use these buttons to make adjustments or selections in the onscreen menu. 1 3 1 2 1 Volume and Channel buttons are located on the side of the LCD TV cabinet. C Cable/cable box TV Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very simple. Follow the steps below to connect your cable signal to your new television. Direct Cable Connections: This connection will supply Stereo sound to the LCD TV. 1 Connect the open end of the round Cable Company supplied cable to the 75Ω input on the bottom of the TV. Screw it down finger tight. Cable signal coming from Cable Company (Round 75Ω coaxial cable) Jack Panel at Bottom of LCD TV 1 Cable Box with RF Inputs/Outputs Connection: This connection will NOT supply Stereo sound to the LCD TV. The sound from the cable box will be mono. 1 Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of the Cable Box. 2 Using a separate round coaxial cable, connect one end to the OUT(put) (TO TV) plug on the back of the Cable Box. 3 Connect the other end of the round coaxial cable to the 75 input on the bottom of the television. Screw it down finger tight. NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4, then tune the cable box on the TV to the corresponding channel. Once tuned, change channels at the cable box, not the television. Cable Signal IN from the Cable Company 1 2 Output Channel Switch Jack Panel Back of Cable Box Round 75Ω Coaxial Cable Jack Panel at Bottom of LCD TV 3 Cable Box with Audio/Video Outputs Connection: This connection will supply Stereo sound to the LCD TV. 1 Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of the Cable Box. 2 Using an RCA type Video Cable, connect one end of the cable to the Video (yellow) (or ANT, your cable box may be labeled differently) Out jack on the cable box and the other end to the Video end of the composite adapter included with the LCD TV. 3 Using an RCA type Audio Left and Right Cable, connect one end to the left and right Audio Out L & R jacks (red & white) on the cable box. Connect the other ends to the Audio end of the composite adapter cable included with the In jack on the bottom of the LCD TV. NOTE: Use the AV+ button and the Number 1 button on the LCD TV remote control to tune to the AV1 channel for the cable box signal. Once tuned, change channels at the cable box, not the television. Pressing the AV+ button repeatedly will scroll all the AV Input channels, including the presently tuned channel. Cable Signal IN from the Cable Company 1 Video Cable (Yellow) 2 Jack Panel Back of Cable Box with A/V Outputs Audio Cables L & R (Red, White) Jack Panel at Bottom of LCD TV 3 D Antenna Connection A combination antenna receives normal broadcast chan nels (VHF 2-13 and UHF 1469). Your connection is easy because there is only one 75Ω (ohm) antenna plug on the back of your LCD TV, and that' s where the antenna goes. If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the LCD TV. 1 If your antenna has flat, twin-lead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300- to 75-ohm adapter. 2 Push the round end of the adapter (or antenna) onto the 75 (ohm) plug on the bottom of the LCD TV. If the round end of the antenna wire is threaded, screw it down finger tight. Outdoor or Indoor Antenna (Combination VHF/UHF). The combination antenna receives normal broadcast channels 2-13 (VHF) and 14-69 (UHF). Twin Lead Wire 1 300 to 75-ohm Adapter 2 Jack Panel at Bottom of LCD TV Round 75Ω Coaxial Cable from Antenna E AV1 Inputs The audio/video input jacks on the bottom panel of the TV are for direct picture and sound connections between the TV and a VCR (or similar device) that has audio/video output jacks. 1 Connect the AV1 In(put) cable to one end of an RCA type VIDEO (yellow) cable to the supplied Audio/Video adapter. Connect the other end of the Adapter to the AV1 in jack on the bottom of the TV. 2 Connect the AV1 In(put) cable to one end of the RCA type AUDIO (red and white) cables to the supplied Audio/Video adapter. 4 3 Turn the VCR or accessory device and the LCD TV ON. 4 Press the AV+ button and the number 1 button on the remote control to select the AV1 channel for the accessory device. AV1 will appear in the upper left corner on the TV screen when tuned properly. You can also press and hold the AV+ button to toggle through the various channels until AV1 appears on the 4 screen. 5 With the VCR (or accessory device) ON and a prerecorded tape (CD, DVD, etc.) inserted, press the PLAY button to view the tape on the television. Tune to AV1 channel Jack Panel at Bottom of LCD TV Audio IN (red/white) 2 Back of VCR (or accessory device) Video IN 5 (yellow) 1 VCR (or accessory device) equipped with video and Audio output jacks 3 F Component inputs (CVI) Component Video inputs provide the highest possible color and picture resolution in the playback of digital signal source material, such as with DVD players. 1 Connect the Component (Y , Pb, Pr) Video OUT jacks from the DVD player (or similar device) to the COMP(onent) VIDEO Input (Y green, Pb blue, Pr red) jacks on the bottom of the TV. When using the Component Video Inputs, it is best not to connect a signal to the AV1 in Video Jack. 2 Connect the red and white AUDIO CABLES to the Audio (left and right) output jacks on the rear of the accessory device to the Audio Adapter supplied (L and R). Connect the adapter into the AV1 In Input Jacks on the TV. 3 Turn the TV and the DVD (or digital accessory device) ON. 4 Press the AV+ on the remote control repeatedly until CVI appear in the upper left corner of the TV screen. 5 Insert a DVD disc into the DVD player and press the PLAY π button on the DVD Player. Note: - When using additional accessories, only one external source will be audible, as there is only one AV1 Input jack. - The CVI input is for non-progressive input. For progressive input, please follow the HD connection. 4 1 Jack Panel at Bottom of LCD TV Audio cables (red/white) 2 Component Video cables (green, blue, red) 4 3 5 Accessory device equipped with component Video outputs. The CVI connection will be dominate over the AV1 in Video Input. When a Component Video Device is connected as described, it is best not to have a video signal connected to the AV1 in Video Input jack. Helpful Hint: The description for the component video connectors may differ depending on the DVD player or accessory digital source equipment used (for example, Y, Pb, Pr; Y, B-Y, R-Y ; Y, Cr, Cb). Refer to your DVD or digital accessory owner's manual for definitions and connection details. G HD (High Definition) inputs If you are using a High Definition receiver that can transmit high definition programming, the TV can accept those signals through the HD Inputs located on the bottom of the LCD TV. 1 For Analog Connection, use Component Video cables to connect the Component (Y, Pb, Pr) Video Out jacks of the HD Receiver (or similar device) to the VGA adapter (supplied with the LCD TV). Connect the other end of the adapter to the VGA Input jacks on the bottom of the LCD TV. 2 Connect the red and white audio adapter to RCA type Audio Cables. Connect the audio adapter to the PC/HD Audio Input jack on the bottom of the LCD TV. 3 Turn the TV and the HD Receiver ON. 4 Press the HD Mode button to set the TV into the HD Mode and tune to the HD signal. Note: The Audio/Video cables needed for this connection are not supplied with your TV. Please contact your dealer or Philips at 1-888-PHILIPS (744-5477) for information about purchasing the needed cables. 12 Jack Panel at Bottom of LCD TV 4 Audio cables Component Video cables (green, blue, red) 3 HD Receiver equipped with component Video outputs Rear of HD Receiver (Illustration is for reference only. Your HD Receiver jack panel may be labeled differently H PC (monitor) inputs This LCD TV can be used as a PC Monitor. Your computer will have to be equipped with a VGA type video output and VGA cable. 1 Connect one end of the VGA Video cable to the Monitor (video) output on the computer to the PC Input (VGA) jack on the bottom of the LCD TV. You can use the HDMI cable if your computer has HDMI capability 2 Connect the AUDIO PC/HD cable of the TV to the Audio output on the PC. 3 Turn the LCD TV and the Computer ON. 4 Press the VGA button to set the TV into the HD Mode and tune to the computer's signal. 4 Note: For the display resolutions available to your LCD TV, refer to the Operating Instruction Manual Please contact your dealer or Philips at 1-888-PHILIPS (744-5477) for information about purchasing the needed cables. I AV3 inputs The Rear jacks allow for extra accessory device connections for items such as cameras or gaming stations. 1 Connect the VIDEO (yellow) adapter cable to the VIDEO IN jack on the rear of the TV. Connect the other end of the VIDEO (yellow) cable to an RCA type VIDEO Cable. Connect that cable to the VIDEO OUT jack on the back of the 4 accessory device being used. Note: An S-Video cable can be used in place of the yellow Video cable if your device is equiped with an S-Video Output. S-Video provides better video playback. 2 Connect the AUDIO (red and white) adapter cable to an RCA type Audio Cable. Connect the other ends of the AUDIO (red and white) cables to the AUDIO (left and right) OUT jacks on the rear of the accessory device being used. 3 Turn the accessory device and the LCD TV ON. 4 Press the AV+ button and the number 3 button on the remote control to select the AV3 channel for the accessory device. REAR will appear in the upper left corner on the TV screen when tuned properly. 5 With the accessory device ON, press the PLAY button to activate the playback on the television. 11 2 Jack Panel at Bottom of LCD TV VGA cable OR HDMI cable Audio cable PC 3 Jack Panel at rear of LCD TV 1 Video cable S-Video cable 1 Accessory device (camera, DVD, VCR, etc.) Audio cable Accessory device jack panel 52 Note: an S-Video cable can be used in place of the yellow Video cable if desired. J Headphone output The Headphone jack can be used to connect to a headphone. If connected to a headphone, there will be no sound from the TV speakers. The sound willcome from the audio system of the headphone. 1 Connect Headphone jack ocated on the right rear of the LCD TV to your headphone set. 2 Turn the TV and headphone ON. TV sound can be heard through the headphone. Jack Panel at rear of LCD TV Headphone cable 2 1 Headphone K Remote control batteries To load the supplied batteries into the remote: 1 Remove the battery compartment door on the back of the remote. 2 After removing the plastic isolation sheet from the battery, place the battery (3V) in the remote. Be sure the (+) and (-) ends of the batteries line up correctly (the inside of the case is marked). 3 Reattach the battery compartment door. Lithium battery (3V) Battery Compartment Door Be sure to point the remote at the remote sensor window on the front of the television when using the remote control to operate the television Remote Control (shown from the bottom) Note: The plastic isolation sheet must be removed for the remote control to function. L Remote control buttons Streamium functions 1 10 2 3 4 11 5 IMPORTANT Press the SELECT button repeatedly 6 12 on the remote control until the indicator is lighted up at STREAM to allow you to access the Streamium 13 functions. 7 8 9 TV functions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IMPORTANT Press the SELECT button repeatedly on the remote control until the indicator is lighted up at TV to allow you to access the LCD TV functions. 15 16 17 1 Power button - Power Streamium LCD TV off (to standby). - Power on the Streamium LCD TV with the INTERNET or HOME LINK button. 2 Playback control buttons Playback (Play/Pause/Previous/Next) functions for multimedia content. 3 Coloured menu buttons For selecting or activating the color-coded option from the on-screen menu. 4 Internet source button - Selects the Internet as your sorce of multimedia content. - Requires a broadband Internet access of minimum 256 kbps, higher recommended. 5 Cursor buttons (Left, Right, Up, Down) Press these buttons to highlight, select, and adjust items on the TV's onscreen menu. 6 Menu button Accesses the Streamium menu settings. 7 Volume (+) or (-) buttons Increase or decrease volume. 8 Shuffle button (Home Link only) Selects the Shuffle mode. 9 Number/Text buttons For entering numbers and SMS-style TEXT. 10 Select mode buttons Allows you to select TV, DMR or STREAM mode. 11 Home Link source button Selects the Home Link as your sorce of multimedia content. 12 OK/Play button Confirms selection and start playing content. 13 Repeat button (Home Link only) Selects the repeat mode. 1 Power button Power Streamium LCD TV ON and OFF. 2 AV+ button Press button followed by the Number 1 or 2. Number 1 allows you to select AV1 (CVI), Number 2 to select to select Rear channel. 3 - Sleeptimer button Set the TV to automatically turn itself OFF at a given amount of time. - Surf button Selects previously viewed channels. You canplace up to 10 channels in memory. Then by pressing the SURF button you can quickly view the select channels. - PIP (Picture-in-Picture) buttons Function not available. 4 Mode buttons Press TV/PC/Radio/HD button to enter TV, PC, Radio or HD mode directly. 5 Format button Press to toggle the different screen format options. 6 Cursor buttons (Left, Right, Up, Down) Press these buttons to highlight, select, and adjust items on the TV's onscreen menu. 7 Menu button Press to enter and also exit On-Screen menu. 8 Mute button Press to turn the TVsound OFF . Press again to return the sound to its previous level. 9 Volume (+) or (-) buttons Increase or decrease volume. 10 Auto Picture buttons Allows you to acess and select the different types of pictures setting. 11 Number buttons Press the number buttons for direct access to the TV channels. For a 2-digit channel, enter the 2nd digit before the dash disappears. For a 3-digit channel, enter the first digit followed the next 2 digits. 12 Status button Press to see the current channel number on the TV screen. Also press to exit the menu. 13 Select mode buttons Allows you to select TV, DMR or STREAM mode. 14 Program List button Press to display a list of channel numbers. Each channel will appear as a selectable menu item. When in Accessory mode, it confirms selections or adjustments in Accessory device. 15 Auto Sound button Allows you to acess and select the different types of sound setting. 16 Channel (+) or (-) buttons Press to access the next or previous channel. 17 CC button Press to select Closed Captioning options within the menu.