Poulan 271150 User Manual - Page 20

Service And Adjustments

Get Poulan 271150 PDF manuals and user guides View all Poulan 271150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Depress clutch/brake pedal fully and set parking brake. 2. Place gearshift lever in neutral (N) position. 3. Place attachment clutch in "DISENGAGED" position. 4. Turn ignition key to "STOP" and remove key. 5. Make sure the blades and all moving parts have completely stopped. 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TRACTOR TO REMOVE MOWER Mower will be easier to remove from the right side of tractor. 1. Place attachment clutch in "DISEN- GAGED" position. 2. Move attachment lift lever forward to lower mower to its lowest position. 3. Roll belt off engine pulley. 4. Remove small retainer spring, and remove clutch spring off pulley bolt. 5. Remove large retainer spring, slide collar off and push housing guide out of bracket. 6. Disconnect anti-sway bar from chassis bracket by removing retainer spring. 7. Disconnect suspension arms from rear deck brackets by removing retainer springs. 8. Disconnect front links from deck by removing retainer springs. 9. Raise lift lever to raise suspension arms. Slide mower out from under tractor. IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame. TO INSTALL MOWER 1. Raise attachment lift lever to its highest position. 2. Slide mower under tractor with deflector shield to right side of tractor. 3. Lower lift lever to its lowest position. 4. Connect front links to mower deck and secure with retainer springs. 5. Connect suspension arms to rear deck brackets and secure with retainer springs. 6. Connect anti-sway bar to chassis bracket and secure with retainer spring. 7. Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring. 8. Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring. 9. Install belt onto engine pulley. Flat Washer Clutch Spring Small Retainer Clutch Spring Spring Small Retainer Spring Suspension Arms Square Hole Engine Pulley Retainer Spring Anti-Sway Bar 38 Front Link 42 Retainer Springs (Both Sides) Collar Housing Guide Large Retainer Spring Bracket Deflector Shield 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
20
38
42
WARNING:
TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER-
VICE OR ADJUSTMENTS:
1.
Depress clutch/brake pedal fully and set parking brake.
2.
Place gearshift lever in neutral (N) position.
3.
Place attachment clutch
in “DISENGAGED” position.
4.
Turn ignition key to “STOP” and remove key.
5.
Make sure the blades and all moving parts have completely stopped.
6.
Disconnect spark plug wire from spark plug and place wire where it cannot
come in contact with plug.
TRACTOR
SERVICE AND ADJUSTMENTS
Suspension
Arms
Retainer
Spring
Anti-Sway
Bar
Housing
Guide
Collar
Large Retainer
Spring
Clutch
Spring
Small Retainer
Spring
Bracket
Retainer Springs
(Both Sides)
Front Link
Engine
Pulley
Square Hole
Deflector Shield
TO REMOVE MOWER
Mower will be easier to remove from the
right side of tractor.
1.
Place attachment clutch in “DISEN-
GAGED” position.
2.
Move attachment lift lever forward to
lower mower to its lowest position.
3.
Roll belt off engine pulley.
4.
Remove small retainer spring, and
remove clutch spring off pulley bolt.
5.
Remove large retainer spring, slide
collar off and push housing guide out
of bracket.
6.
Disconnect anti-sway bar from chassis
bracket by removing retainer spring.
7.
Disconnect suspension arms from rear
deck brackets by removing retainer
springs.
8.
Disconnect front links from deck by
removing retainer springs.
9.
Raise lift lever to raise suspension
arms. Slide mower out from under trac-
tor.
IMPORTANT:
If an attachment other than
the mower deck is to be mounted on the
tractor, remove the front links and hook
the clutch spring Into square hole in frame.
TO INSTALL MOWER
1.
Raise attachment lift lever to its highest
position.
2.
Slide mower under tractor with deflec-
tor shield to right side of tractor.
3.
Lower lift lever to its lowest position.
4.
Connect front links to mower deck and
secure with retainer springs.
5.
Connect suspension arms to rear
deck brackets and secure with retainer
springs.
6.
Connect anti-sway bar to chassis
bracket and secure with retainer spring.
7.
Push clutch cable housing guide into
bracket, slide collar onto guide and
secure with large retainer spring.
8.
Place flat washer and clutch spring on
idler pulley bolt and secure with small
retainer spring.
9.
Install belt onto engine pulley.
Small Retainer
Spring
Clutch Spring
Flat Washer