ProForm 1095 Zlt Treadmill Uk Manual - Page 20

The Power Cord.

Page 20 highlights

Remove the three 3/4" Screws (10) and carefully pivot the Motor Hood (57) off. 10 57 Locate the Reed Switch (64) and the Magnet (42) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch. 1/8 in. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If nec- 12 42 essary, loosen the Reed Switch Screw (12), move 64 the Reed Switch slightly, and then retighten the 43 Screw. Then, reattach the Motor Hood (not shown). Top Reattach the Hood Screws (not shown), if neces- View sary. Raise the Uprights. Run the treadmill for a few minutes to check for a correct speed reading. PROBLEM: The incline of the treadmill does not change correctly SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system. PROBLEM: The walking belt slows when walked on SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m (5 ft.). b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 2-3 in. Idler Roller Bolts c. If the walking belt still slows when walked on, see the front cover of this manual. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

20
Remove the three 3/4" Screws (10) and carefully
pivot the Motor Hood (57) off.
Locate the Reed Switch (64) and the Magnet (42)
on the left side of the Pulley (43). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm).
If nec-
essary, loosen the Reed Switch Screw (12), move
the Reed Switch slightly, and then retighten the
Screw. Then, reattach the Motor Hood (not shown).
Reattach the Hood Screws (not shown), if neces-
sary. Raise the Uprights. Run the treadmill for a
few minutes to check for a correct speed reading.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION:
a. With the key in the console, press one of the Incline buttons.
While the incline is changing, re-
move the key.
After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION:
a. If an extension cord is needed, use only a 3-conductor, 1 mm
2
(14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and
UNPLUG
THE POWER CORD.
Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
c. If the walking belt still slows when walked on, see the front cover of this manual.
Top
View
42
12
64
1/8 in.
43
Idler Roller Bolts
2–3 in.
b
57
10