ProForm 12.0 Ne Elliptical English Manual - Page 31

Maintenance And Troubleshooting

Get ProForm 12.0 Ne Elliptical PDF manuals and user guides View all ProForm 12.0 Ne Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

MAINTENANCE AND TROUBLESHOOTING MAINTENANCE HOW TO ADJUST THE REED SWITCH Inspect and tighten all parts of the elliptical regularly. Replace any worn parts immediately. To clean the elliptical, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. CONSOLE TROUBLESHOOTING If the console does not turn on, make sure that the power cord is fully plugged in. If the console does not display your heart rate when you hold the handgrip heart rate monitor, or if the displayed heart rate appears to be too high or too low, see step 5 on page 20. If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, first unplug the power cord. Next, use a flat screwdriver and carefully pry the left Disc Cover (55) off the left Disc (71). 71 55 If the console does not display your heart rate when you use the chest heart rate monitor, see TROUBLESHOOTING on page 13. If it is difficult for you to touch the correct buttons on the screen, the screen may not be properly calibrated. To calibrate the screen, see step 5 on page 27. Next, turn the left Crank Arm (20) until one of the Magnets (43) on the Pulley (19) is aligned with the Reed Switch (38). Then, loosen, but do not remove, the two M4 x 16mm Screws (104), slide the Reed Switch (38) slightly closer to or away from the Magnet (43), and retighten the Screws. INCLINE SYSTEM TROUBLESHOOTING If the ramp does not move to the correct incline level, see step 4 on page 27 and calibrate the incline system. HOW TO GREASE THE ROLLERS See the EXPLODED DRAWING near the end of this manual. If the Large Rollers (51) squeak when moving on the Tracks (11), first clean the Tracks and the Large Rollers with a lint-free cloth and rubbing alcohol. Next, apply one packet (3 grams) of the included PTFE grease to each Track. Use a lint-free cloth or your fingers to spread the grease evenly along the Tracks. Then, wipe off any excess grease. If the included grease packets have been used or lost, use a highquality clear or white grease instead. 104 38 43 19 20 Then, plug in the power cord and turn the left crank arm for a moment. Repeat the procedure above, if necessary, until the console displays correct feedback. Then, reattach the left disc. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
31
MAINTENANCE
Inspect and tighten all parts of the elliptical regularly.
Replace any worn parts immediately.
To clean the elliptical, use a damp cloth and a small
amount of mild soap.
IMPORTANT: To avoid damage
to the console, keep liquids away from the console
and keep the console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console does not turn on, make sure that the
power cord is fully plugged in.
If the console does not display your heart rate when
you hold the handgrip heart rate monitor, or if the dis-
played heart rate appears to be too high or too low, see
step 5 on page 20.
If the console does not display your heart rate
when you use the chest heart rate monitor, see
TROUBLESHOOTING on page 13.
If it is difficult for you to touch the correct buttons on the
screen, the screen may not be properly calibrated. To
calibrate the screen, see step 5 on page 27.
INCLINE SYSTEM TROUBLESHOOTING
If the ramp does not move to the correct incline level,
see step 4 on page 27 and calibrate the incline
system.
HOW TO GREASE THE ROLLERS
See the EXPLODED DRAWING near the end of this
manual. If the Large Rollers (51) squeak when mov-
ing on the Tracks (11), first clean the Tracks and the
Large Rollers with a lint-free cloth and rubbing alcohol.
Next, apply one packet (3 grams) of the included PTFE
grease to each Track. Use a lint-free cloth or your
fingers to spread the grease evenly along the Tracks.
Then, wipe off any excess grease. If the included
grease packets have been used or lost, use a high-
quality clear or white grease instead.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first
unplug the power cord.
Next, use a flat
screwdriver
and carefully
pry the left Disc
Cover (55) off
the left Disc
(71).
Next, turn the left Crank Arm (20) until one of the
Magnets (43) on the Pulley (19) is aligned with the
Reed Switch (38). Then, loosen, but do not remove,
the two M4 x 16mm Screws (104), slide the Reed
Switch (38) slightly closer to or away from the Magnet
(43), and retighten the Screws.
Then, plug in the power cord and turn the left crank
arm for a moment. Repeat the procedure above, if
necessary, until the console displays correct feedback.
Then, reattach the left disc.
55
71
43
38
19
104
20
MAINTENANCE AND TROUBLESHOOTING