ProForm 360 P Instruction Manual - Page 8

6. Place the Console Base (47) on the Right Handrail (72) 6 and the Left Handrail (not shown). Attach the Console Base with four 3/4" Screws (2) (only two Screws are shown). Do not overtighten the Screws. Insert the Wire Harness (42) through the two indicated nylon ties on the Console Base (47). Next, touch the Right Handrail (72) to discharge any static. Refer to drawing 6c. Find the connector on the end of the Wire Harness (42). Insert the connector into the red socket be- neath the Console (43). The connector should slide eas- ily into the socket and snap into place. If the connector does not slide easily and snap into place, turn the connec- 2 tor and then insert it. Make sure that the connector and wires appear as shown in drawing 6a. IF THE CONNECTOR IS NOT INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 47 42 Ties 72 43 6a 42 7. Insert the excess Wire Harness (42) into the large hole in the side of the Right Handrail (72). Securely tighten the nylon ties on the bottom of the Console Base (47) to prevent the Wire Harness from slipping. Then, cut off the ends of the nylon ties. Route the Wire Harness (42) through the indicated opening in the Console Base (47). Attach the Wire Cover (44) to the Console Base with a 1/2" Silver Screw (48). Tighten two 3/4" Screws (2) into the Console Base (47). Firmly tighten the bolts and screws used in steps 2, 3, 4, and 6. 7 Ties 42 Opening 47 44 72 48 2 8. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included hex keys in a secure place. The large hex key is used to adjust the walking belt (see page 16). To protect the floor or carpet, place a mat under the treadmill. 8 HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION: You must be able to safely lift 20 kg (45 lbs.) to raise, lower, or move the treadmill. 1. Hold the treadmill with your hands in the locations shown at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the treadmill until the frame is past the latch pin. Slowly release the latch knob. Make sure that the frame is securely held by the latch pin. To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F). Frame Latch Knob Latch Pin Engaged HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the frame is securely held by the latch pin. 1. Hold the upper ends of the handrails. Place one foot on the base as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution whilst moving the treadmill. Do not move the treadmill over an uneven surface. 3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position. Base Front Wheels 13