ProForm 410 Trainer Treadmill English Manual - Page 6

Assembly - key

Get ProForm 410 Trainer Treadmill PDF manuals and user guides View all ProForm 410 Trainer Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

ASSEMBLY To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubricant on the walking belt, simply wipe off the lubricant with a soft cloth and mild, non-abrasive cleaner. Assembly requires the included hex keys and your own Phillips screwdriver , adjustable wrench , and scissors . Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do not use power tools for assembly. M8 Star M10 Star Washer (10)-4 Washer (8)-4 M10 Nut (33)-2 Base Pad Spacer (71)-2 Bolt Spacer (79)-4 M4.2 x 18mm M4.2 x 19mm Latch Screw (101)-2 Screw (1)-6 M4.2 x 25mm Screw (2)-4 #8 x 1/2" Screw (3)-1 M8 x 25mm Bolt (6)-4 M10 x 50mm Bolt (27)-2 M10 x 96mm Bolt (5)-4 1. Make sure that the power cord is unplugged. 1 With the help of a second person, carefully tip the treadmill onto its left side. Partially fold the Frame (48) so that the treadmill is more stable; do not fully fold the Frame yet. Cut the tie securing the Upright Wire (77) to the Base (85). Locate a tie in the indicated hole in the Base, and use the tie to pull the Upright Wire out of the hole. Attach a Base Pad (81) to the Base (85) in the location shown with an M4.2 x 25mm Screw (2) and a Base Pad Spacer (71). Then, attach another Base Pad (81) with only an M4.2 x 25mm Screw (2). 6 85 Hole 48 71 81 2 81 2 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
6
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons.
Set the treadmill in a cleared area and remove all packing materials;
do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If
there is lubricant on the walking belt, simply wipe off the lubricant with a soft cloth and mild, non-abrasive cleaner.
Assembly requires the included hex keys
and your own Phillips screwdriver
,
adjustable wrench
, and scissors
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly.
Note: If a part is not in the parts bag, check to see if it is preattached to
one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts, do
not use power tools for assembly.
1.
Make sure that the power cord is unplugged.
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (48) so that the treadmill is more stable;
do not fully fold the Frame yet.
Cut the tie securing the Upright Wire (77) to the
Base (85). Locate a tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
Attach a Base Pad (81) to the Base (85) in the
location shown with an M4.2 x 25mm Screw (2)
and a Base Pad Spacer (71). Then, attach an-
other Base Pad (81) with only an M4.2 x 25mm
Screw (2).
85
2
48
81
Base Pad Spacer (71)–2
M8 Star
Washer (10)–4
M4.2 x 19mm
Screw (1)–6
M8 x 25mm
Bolt (6)–4
#8 x 1/2" Screw
(3)–1
M10 Nut
(33)–2
M4.2 x 25mm
Screw (2)–4
M4.2 x 18mm
Latch Screw (101)–2
M10 Star
Washer (8)–4
M10 x 96mm Bolt (5)–4
Bolt Spacer (79)–4
M10 x 50mm Bolt (27)–2
1
81
2
77
Hole
71