ProForm 510 Uk Manual - Page 12

Maintenance And Trouble-shooting

Get ProForm 510 PDF manuals and user guides View all ProForm 510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

MAINTENANCE AND TROUBLE-SHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department. PROBLEM: THE POWER DOES NOT TURN ON SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) If an extension cord is needed, use only a 1 mm2 (14gauge) cord of 1,5 m (5 ft.) or less in length. Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. PROBLEM: THE POWER TURNS OFF DURING USE c Tripped Tripped Reset Reset SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. c. Remove the key from the console. Reinsert the key fully into the console. d. If the treadmill still will not run, please call our Customer Service Department. PROBLEM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 5 on page 6. Most problems are the result of drained batteries. b. First remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from the hood. Carefully remove the hood. Locate the Reed Switch (8) and the Magnet (14) on the left side of the Pulley (17). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 3 mm (1/8 in.). If necessary, loosen the Reed Switch Screw (77) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. b 17 77 8 14 3 mm Top View 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
12
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM:
THE POWER DOES NOT TURN ON
SOLUTION:
a.
Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG
IN THE POWER CORD on page 7.) If an extension cord is needed, use only a 1 mm
2
(14-
gauge) cord of 1,5 m (5 ft.) or less in length. Important: The treadmill is not compatible with
GFCI-equipped outlets.
b.
After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
PROBLEM:
THE POWER TURNS OFF DURING USE
SOLUTION:
a.
Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b.
Make sure that the power cord is plugged in.
c.
Remove the key from the console. Reinsert the key fully into the console.
d.
If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
SOLUTION:
a. Check the batteries in the console. If the batteries need to be replaced, see assembly step 5 on
page 6. Most problems are the result of drained batteries.
b.
First remove the key from the console and
UNPLUG
THE POWER CORD.
Remove the screws from the
hood. Carefully remove the hood. Locate the Reed
Switch (8) and the Magnet (14) on the left side of the
Pulley (17). Turn the Pulley until the Magnet is
aligned with the Reed Switch.
Make sure that the
gap between the Magnet and the Reed Switch is
about 3 mm (1/8 in.).
If necessary, loosen the Reed
Switch Screw (77) and move the Reed Switch slight-
ly. Retighten the Screw. Re-attach the hood, and run
the treadmill for a few minutes to check for a correct
speed reading.
Tripped
Reset
Tripped
Reset
c
14
8
77
b
3 mm
17
Top View