ProForm 595 Pi Treadmill English Manual - Page 8

Console May Be Damaged When The Power

Get ProForm 595 Pi Treadmill PDF manuals and user guides View all ProForm 595 Pi Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Identify the Right Handrail Endcap (91), which does not have a cutout in the bottom, and slide it onto the lower end of the Right Handrail (11). Make sure that the screw hole in the Right Handrail Endcap is at the bottom. Next, hold the Right Handrail near the Right Upright (36), and insert the Wire Harness (28) into the hole in the bottom of the Handrail and out of the indicated hole in the top. Then, remove the tie from the Wire Harness. Set the Right Handrail (11) on the Right Upright (36) while sliding the lower end of the Handrail onto the bracket on the Right Upright. Hand tighten two Handrail Bolts (20) with two Handrail Star Washers (19) into the Handrail and the Right Upright. Next, slide the Right Handrail Endcap (91) against the Right Upright, and tighten an Endcap Screw (95) into the Right Handrail Endcap. Then, tighten the two Handrail Bolts. Make sure that the Wire Harness (28) is not pinched. Attach the Left Handrail (18) and the Left Handrail Endcap (90) to the Left Upright (31) as described above. 6. Hold the Console Base (26) near the Right Handrail (11). Attach the end of the ground wire on the Console Base to the indicated small hole in the Handrail with a Silver Ground Screw (27). Connect the Wire Harness (28) to wire harness on the Console Base (26). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 5 20 18 19 Cutout 90 95 28 31 20 19 11 36 91 95 6 26 27 Ground Wire 28 11 28 7. Set the console assembly on the Handrails (11, 18); insert the excess wiring down into the Right Handrail. 7 Attach the console assembly with four 3/4" Screws (2), 11 two Console Bolts (22), and two 1/4" Star Washers (21) as shown. Make sure that no wires are pinched. Start all four Screws and both Console Bolts before tight- ening any of them. Console Assembly 18 21 2 22 2 21 22 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
8
28
11
6.
Hold the Console Base (26) near the Right Handrail (11).
Attach the end of the ground wire on the Console Base
to the indicated small hole in the Handrail with a Silver
Ground Screw (27).
Connect the Wire Harness (28) to wire harness on the
Console Base (26).
Make sure to connect the connec-
tors properly (see the inset drawing). The connectors
should slide together easily and snap into place.
If
the connectors do not slide together easily and snap into
place, turn one connector and try again.
IF THE CON-
NECTORS ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
27
26
Ground
Wire
22
7.
Set the console assembly on the Handrails (11, 18); in-
sert the excess wiring down into the Right Handrail.
Attach the console assembly with four 3/4” Screws (2),
two Console Bolts (22), and two 1/4” Star Washers (21)
as shown.
Make sure that no wires are pinched. Start
all four Screws and both Console Bolts before tight-
ening any of them.
2
21
2
11
18
6
7
5.
Identify the Right Handrail Endcap (91), which does
not
have a cutout in the bottom, and slide it onto the lower
end of the Right Handrail (11). Make sure that the screw
hole in the Right Handrail Endcap is at the bottom. Next,
hold the Right Handrail near the Right Upright (36), and
insert the Wire Harness (28) into the hole in the bottom
of the Handrail and out of the indicated hole in the top.
Then, remove the tie from the Wire Harness.
Set the Right Handrail (11) on the Right Upright (36)
while sliding the lower end of the Handrail onto the
bracket on the Right Upright. Hand tighten two Handrail
Bolts (20) with two Handrail Star Washers (19) into the
Handrail and the Right Upright. Next, slide the Right
Handrail Endcap (91) against the Right Upright, and
tighten an Endcap Screw (95) into the Right Handrail
Endcap. Then, tighten the two Handrail Bolts.
Make
sure that the Wire Harness (28) is not pinched.
Attach the Left Handrail (18) and the Left Handrail
Endcap (90) to the Left Upright (31) as described above.
36
31
95
95
91
90
Cutout
28
20
19
18
19
20
11
5
28
Console Assembly
21
22