ProForm Crosswalk 380x Canadian English Manual - Page 21

One Of The Upper Body Arms Squeaks During Use

Get ProForm Crosswalk 380x PDF manuals and user guides View all ProForm Crosswalk 380x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

PROBLEM: The walking belt slows when walked on SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 5-7 cm (2-3 in.) off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 5-7 cm Rear Roller Adjustment Bolts c. If the walking belt still slows when walked on, please call toll-free 1-888-936-4266. PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking a belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered. b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using b the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tight- ened, you should be able to lift each side of the walk- ing belt 5-7 cm (2-3 in.) off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened. PROBLEM: ONE OF THE UPPER BODY ARMS SQUEAKS DURING USE SOLUTION: a. Correcting this problem requires a small amount of white marine grease, available at most hardware a 105 stores. Turn the Resistance Knob (109) counterclock- 24 107 wise until it can be removed. Remove the Resistance Cone (108) and the Upper Body Arm (117), along with the Resistance Plate (127), Spring Washer (111), Thrust Washers (112), and Thrust Bearing (113). (Note: If the Resistance Sleeve [107] comes out of the Resistance Bracket [105], press it back in.) Apply a thin layer of white marine grease to the outer surface of the Resistance Cone (108). Reattach all parts in 112 111 108 109 127 113 110 the order shown at the right. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
21
PROBLEM: The walking belt slows when walked on
SOLUTION:
a.
Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b.
If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be-
come damaged. Remove the key and
UNPLUG THE
POWER CORD
. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 5–7
cm (2–3 in.) off the walking platform. Be careful to
keep the walking belt centered. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.
c.
If the walking belt still slows when walked on, please call toll-free 1-888-936-4266.
PROBLEM:
The walking belt is off-center or slips when walked on
SOLUTION:
a.
If the walking belt is off-center, first remove the key
and
UNPLUG THE POWER CORD
.
If the walking
belt has shifted to the left,
use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn;
if
the walking belt has shifted to the right,
turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b.
If the walking belt slips when walked on, first remove
the key and
UNPLUG THE POWER CORD
. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 5–7 cm (2–3 in.) off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
PROBLEM:
ONE OF THE UPPER BODY ARMS SQUEAKS DURING USE
SOLUTION:
a. Correcting this problem requires a small amount of
white marine grease, available at most hardware
stores. Turn the Resistance Knob (109) counterclock-
wise until it can be removed. Remove the Resistance
Cone (108) and the Upper Body Arm (117), along with
the Resistance Plate (127), Spring Washer (111),
Thrust Washers (112), and Thrust Bearing (113).
(Note: If the Resistance Sleeve [107] comes out of the
Resistance Bracket [105], press it back in.) Apply a
thin layer
of white marine grease to the outer surface
of the Resistance Cone (108). Reattach all parts in
the order shown at the right.
b
a
Rear Roller Adjustment Bolts
5–7 cm
b
107
105
24
109
112
111
127
113
a
110
108