Pyle HTG559BT Instruction Manual
Pyle HTG559BT Manual
View all Pyle HTG559BT manuals
Add to My Manuals
Save this manual to your list of manuals |
Pyle HTG559BT manual content summary:
- Pyle HTG559BT | Instruction Manual - Page 1
- Pyle HTG559BT | Instruction Manual - Page 2
optimum performance, it is highly recommended that you read this Owners Manual before beginning installation. WARNING High powered audio systems in a vehicle 5 CONTROL FUNCTIONS 7 SPEAKER DIAGRAMS MONO CHANNEL 9 TROUBLESHOOTING GUIDE 14 WARNINGS 14 SPECIFICATION 15 2 www.Lanzar.com - Pyle HTG559BT | Instruction Manual - Page 3
PLANNING YOUR SYSTEM Before beginning the installation, consider the following: 1. Do you plan to add additional mobile electronics equipment in the future? If you plan to expand your system by adding other components sometime in the future, ensure adequate space is left and cooling requirements are - Pyle HTG559BT | Instruction Manual - Page 4
WIRING CONNECTION 1. Ground: To Vehicle Chassis To avoid unwanted ignition noise caused by ground loop, it is essential that the Ampli er be grounded to a clean, bare, metal surface of the vehicle's Chassis NOTE: GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT. (1 METER). 2. +12 Volt (Fused) - Pyle HTG559BT | Instruction Manual - Page 5
HTG889 PANEL LAYOUT HTG559BT - HTG669BT Front View HTG889 Front View www.Lanzar.com 5 - Pyle HTG559BT | Instruction Manual - Page 6
Rear View HTG559BT HTG669BT HTG889 6 www.Lanzar.com - Pyle HTG559BT | Instruction Manual - Page 7
CONTROL FUNCTIONS 1. RCA Input jacks These RCA input jacks are for use with source units that have RCA or Line level outputs. A source unit with a minimum level of 200mV is required for proper operation. The use of high quality twisted pair cables is recommended to decrease the possibility of - Pyle HTG559BT | Instruction Manual - Page 8
6. LED Will illuminate GREEN to indicate the ampli er is on and operating normally, and will be illuminated RED if the ampli er shuts down due to short circuit, DC o set, or overheating detected by on board protection circuitry. 7. Auxiliary Outputs The Auxiliary outputs o er LANZAR ampli ers easy, - Pyle HTG559BT | Instruction Manual - Page 9
System Diagrams 5 Channel Systems HTG559BT www.Lanzar.com 9 - Pyle HTG559BT | Instruction Manual - Page 10
System Diagrams 6 Channel Systems HTG669BT 10 www.Lanzar.com - Pyle HTG559BT | Instruction Manual - Page 11
System Diagrams www.Lanzar.com 11 - Pyle HTG559BT | Instruction Manual - Page 12
System Diagrams 8 Channel Systems HTG889 12 www.Lanzar.com - Pyle HTG559BT | Instruction Manual - Page 13
System Diagrams www.Lanzar.com 13 - Pyle HTG559BT | Instruction Manual - Page 14
TROUBLESHOOTING GUIDE WARNINGS Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care when to work near the gas tanks, lines, or - Pyle HTG559BT | Instruction Manual - Page 15
Speci cation HTG889 8-Channel Mosfet Ampli er 2 Ohm Stereo Stable with High Pass and Low Pass Filter Controls Features: • Class "AB" High-Current Dual Discrete Drive Stages • Mosfet PWM Power Supply • Bass Boost Circuit • Bridgeable at 4ohms • 2 Ohm Stereo Stable • Chrome RCA Inputs, Power Speaker - Pyle HTG559BT | Instruction Manual - Page 16
HTG559BT 5-Channel Mosfet Ampli er with Wireless BT Audio Interface 2 Ohm Stereo Stable with High Pass and Low Pass Filter Controls Features: • Wireless BT Audio Interface • Class "AB" High-Current Dual Discrete Drive Stages • Mosfet PWM Power Supply • Bass Boost Circuit • Bridgeable at 4 Ohms • 2 - Pyle HTG559BT | Instruction Manual - Page 17
HTG669BT 6-Channel Mosfet Ampli er with Wireless BT Audio Interface 2 Ohm Stereo Stable with High Pass and Low Pass Filter Controls Features: • Wireless BT Audio Interface • Class "AB" High-Current Dual Discrete Drive Stages • Mosfet PWM Power Supply • Bass Boost Circuit • Bridgeable at 4 Ohms • 2 - Pyle HTG559BT | Instruction Manual - Page 18
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: [email protected]