RCA R52WH76 User Manual - Page 75

Using the TV's Menu System 0 Go Back 1 Signal Strength 2 Channel Search 3 Signal Source 4 Auto Tuning 5 Special Features Main Menu4Connections Front Input Use this screen if you have misplaced your remote control and need a way to tune to a different antenna or to go to the video inputs. Use the arrows to highlight the rectangle then press OK or MENU-OK to scroll to the input you want. You can select a source from the available signal sources. Press OK to continue. 0 Go Back 1 Signal Strength 2 Channel Search 3 Signal Source 4 Auto Tuning 5 Special Features Main Menu Connections Select which input or channel should be automatically tuned when a button listed below is pressed on the remote control. VCR Front Input AUDIO (Audio Receiver/Amp) Not Connected VCR2 Not Connected RCA SAT2 Not Connected DVD Input 2 SAT-CABLE (Satellite or Cable Box) Not Connected Tip: If you indicated in TV Guide Setup that you have a cable box, set the Auto Tuning for SAT•CABLE to "Not Connected". Press OK to select the channel or input that is tuned when the VCR key is pressed on the remote. 0 Go Back 1 Initial Channel 2 Initial Volume 3 Maximum Volume 4 CableCARD Tools 5 CableCARD Reset 6 Remote Setup Main Menu Connections Special Features Select what should occur when power is restored to the TV: Off: Initial Channel is disabled On: Go to last input or channel selected On: Go to Cable Input Channel + - 27 Sub-channel + - 9 Note: An Initial Channel setting of "On" will be enabled only when the TV is plugged back in or electricity is otherwise restored to the TV. Initial Channel is not enabled from the turning on of the TV with the remote or front buttons. Press or to point to an option, then press OK to select it. Press to return to the menu. 0 Go Back 1 Initial Channel 2 Initial Volume 3 Maximum Volume 4 CableCARD Tools 5 CableCARD Reset 6 Remote Setup Main Menu4Connections4Special Features Network Setup CableCARD™ Status CableCARD™ Pairing Conditional Access Press 5 or 6 to point to an option, then press OK to select it. Press 3 to return to the menu. This screen is provided by your local cable TV company. Continue Chapter 4 Signal Source The Signal Source menu allows you to choose the source from which you would like the signal to come: Cable Input, Antenna Input, or Video Inputs. The same can be accomplished using the component buttons if you've set up Auto Tuning on the remote or by pressing the INPUT button. But, if you misplace the remote, this feature gives you another way to tune to a signal source. Auto Tuning This menu lets you specify the various components you have connected to your TV. It lets you program a component button on the remote control (VCR, AUX, DVD, SAT•CABLE, or AUDIO) so that pressing the button automatically turns on the TV and turns the TV to the correct Video Input Channel (go to Chapter 3 for detailed information). Notes: The AUX button by default is set up for an RCA HDTV Tuner receiver. If you have two RCA satellite receivers, you can control each separately. Program the second receiver with the AUX button using the 5001 code. Then use the RCA SAT2 option in the auto tuning menu to set auto tuning. Special Features The special features options are mostly intended for commercial/retail use. Initial Channel You can select the tuner and channel or input that your TV tunes to each time the TV is turned on by plugging it back in. Initial Volume This feature works only if the Initial Channel feature is set to On. Select the volume level that you want when the TV is turned on. Maximum Volume This feature is intended to stop the volume from being turned up too loudly. Set the volume at the loudest level you would want to hear. CableCARD Tools Displays information available for digital cable TV services when a digital cable card is inserted into the back of the TV and you have subscribed to digital cable service. Go to page 10 for more information on using your digital cable card. The CableCARD Tools information might vary according to the brand of card you have inserted into your TV. The graphic to the left is an example of what you might see. Select an option to view more information. Some CableCARD Tools screens might have additional information displayed on more than one page. Use the arrow buttons on the remote to highlight the blue Continue link at the bottom of the page, for example, as the graphic to the left shows, and simply press the OK button on the remote to read more text. If more than one link appears, use the arrow buttons to highlight the one you want. To exit the screen, press CLEAR on the remote. CableCARD Reset If you experience problems with your digital cable, try resetting your digital cable card. Press the right arrow to select Reset and then press the OK button on the remote. If problems persist, contact your cable company. 73