Reebok R 5.10 Elliptical English Manual - Page 8

Tip: Avoid pinching the Main Wire 60.

Get Reebok R 5.10 Elliptical PDF manuals and user guides View all Reebok R 5.10 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

4. Tip: Avoid pinching the Main Wire (60). Insert the Upright (5) into the Main Frame (1). 4 Attach the Upright (5) with four M8 x 16mm Screws (102) and four M8 Split Washers (103); do not tighten the Screws yet. You will tighten the Screws at the end of step 11. 5 103 102 1 Avoid pinching the Main Wire (60) 102 103 103 102 103 102 5. Using a small plastic bag to keep your fingers clean, apply a coat of the included grease to the Upright Axle (48) and to two Wave Washers (118). Tip: Avoid damaging the Main Wire (60). Insert the Upright Axle (48) through the Upright (5) and center it. Slide a Wave Washer (118) onto each side of the Upright Axle. Next, identify the Right and Left Upper Body Legs (6, 7), which are marked with “"Right”" and “"Left”" stickers, and orient them as shown. Slide the Right and Left Upper Body Legs (6, 7) onto the right and left sides of the Upright Axle (48). Tighten an M8 x 16mm Screw (102) and an M8 Washer (95) into each end of the Upright Axle (48) at the same time. 5 60 102 95 118 7 Grease Avoid damaging the Main Wire (60) 5 48 Grease 118 102 95 6 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
4
4.
Tip: Avoid pinching the Main Wire (60).
Insert
the Upright (5) into the Main Frame (1).
Attach the Upright (5) with four M8 x 16mm
Screws (102) and four M8 Split Washers (103);
do not tighten the Screws yet. You will
tighten the Screws at the end of step 11.
5
102
102
102
102
103
103
103
103
1
Avoid pinching the
Main Wire (60)
5
5.
Using a small plastic bag to keep your fingers
clean, apply a coat of the included grease to
the Upright Axle (48) and to two Wave Washers
(118).
Tip: Avoid damaging the Main Wire (60).
Insert
the Upright Axle (48) through the Upright (5) and
center it. Slide a Wave Washer (118) onto each
side of the Upright Axle.
Next, identify the Right and Left Upper Body
Legs (6, 7), which are marked with ²Right³ and
²Left³ stickers, and orient them as shown.
Slide the Right and Left Upper Body Legs (6, 7)
onto the right and left sides of the Upright Axle
(48).
Tighten an M8 x 16mm Screw (102) and an M8
Washer (95) into each end of the Upright Axle
(48) at the same time.
Avoid damaging the
Main Wire (60)
Grease
Grease
95
5
7
102
95
102
118
48
60
6
118