Ricoh AP610N Setup Guide

Ricoh AP610N - Aficio B/W Laser Printer Manual

Get Ricoh AP610N - Aficio B/W Laser Printer PDF manuals and user guides
UPC - 026649023385
View all Ricoh AP610N manuals
Add to My Manuals
Save this manual to your list of manuals

Ricoh AP610N manual content summary:

  • Ricoh AP610N | Setup Guide - Page 1
    Setup Guide 1 Guide to the Printer 2 Setting Up 3 Installing Options 4 Connecting the Printer 5 Configuration 6 Installing the Printer Driver Read this manual carefully before you use this product and keep it handy for future reference. For safe and correct use, please be sure to read the Safety
  • Ricoh AP610N | Setup Guide - Page 2
    certificates, bank drafts, checks, passports, driver's licenses. The preceding list is meant as a guide only and is not inclusive. We assume manual. With this machine refer to the metric version. For good print quality, the supplier recommends that you use genuine toner, maintenance kits and parts
  • Ricoh AP610N | Setup Guide - Page 3
    8 How to Read This Manual 9 1. Guide to the Printer Exterior ...11 Inside...13 Control Panel...14 2. Setting Up Where to Put the Printer 17 Unpacking the Printer and Checking the Contents of the Box 20 Installing the Toner Cartridge 21 Loading Paper ...24 Turning the Power On 26 Selecting the
  • Ricoh AP610N | Setup Guide - Page 4
    5. Configuration Ethernet Configuration 61 IEEE 802.11b (Wireless LAN) Configuration 64 IEEE 1394 Configuration 68 IP over 1394...68 SCSI print...70 6. Installing the Printer Driver Quick Install...71 Install the Operating Instructions 73 INDEX...74 ii
  • Ricoh AP610N | Setup Guide - Page 5
    • The product names of Windows® XP are as follows: Microsoft® Windows® XP Professional Microsoft® Windows® XP Home Edition • The product names of Windows ServerTM 2003 are as follows: Microsoft® Windows ServerTM 2003 Standard Edition Microsoft® Windows ServerTM 2003 Enterprise Edition Microsoft
  • Ricoh AP610N | Setup Guide - Page 6
    Safety Information When using your printer, the following safety precautions should always be followed. In this manual, the following important symbols are used: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. Indicates a
  • Ricoh AP610N | Setup Guide - Page 7
    the power cord or plug with wet hands. • Do not remove any covers or screws other than those specified in this manual. Some parts of power switch and wait for about 15 minutes before cleaning the Registration roller. Not waiting for the printer to cool down can result in a burn. • The supplied power
  • Ricoh AP610N | Setup Guide - Page 8
    set the toner into the fabric and may make removing the stain impossible. • Our products are engineered to meet the highest standards of quality and functionality. When purchasing expendable supplies, we recommend using only those provided by an authorized dealer. • Do not pull out the paper tray
  • Ricoh AP610N | Setup Guide - Page 9
    result in fire or electric shock. • Lifting the paper feed unit carelessly or dropping it may cause injury. • When removing misfed paper, do not touch the fusing section because it becomes very hot. • When you move the printer, remember to unplug the power cord from the wall outlet to avoid a fire
  • Ricoh AP610N | Setup Guide - Page 10
    below. For safety, please follow the instructions and handle the machine as indicated. AGN039S Do not incinerate toner or toner containers. Toner dust may cause flashback when exposed to open flames. The inside of this printer becomes very hot. Do not touch parts with this label (indicating a hot
  • Ricoh AP610N | Setup Guide - Page 11
    about how to configure Energy Saver mode, see "Making Printer Settings with Control Panel", Software Guide as a HTML file on the CD-ROM. ❖ Specifications Energy Saver mode Power Consumption Default Time With Options: 10.5 W or less Printer Only: 6.5 W 30 minutes -Recycled Paper In accordance
  • Ricoh AP610N | Setup Guide - Page 12
    functions, see the relevant parts of the manual. ❖ Setup Guide (this manual) Provides information about printer setup and options. ❖ Maintenance Guide Provides information about paper, replacing supplies, and dealing with paper jams and error messages. ❖ Software Guide (HTML) Provides basic
  • Ricoh AP610N | Setup Guide - Page 13
    manual. This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions safety. If this instruction is not followed, paper might be misfed,
  • Ricoh AP610N | Setup Guide - Page 14
    10
  • Ricoh AP610N | Setup Guide - Page 15
    When printing on custom paper size, printer driver settings are required. Up to 100 sheets of plain paper (80 g/m2, 20 lb.) can be loaded. See "Paper and Other Media Supported by this Printer" and "Loading Paper in the Bypass Tray", Maintenance Guide. AGN010S 4. Output Tray Extension Pull out this
  • Ricoh AP610N | Setup Guide - Page 16
    open the front cover. Remove to install the optional duplex unit or to replace the fusing unit. 10. Power Switch Use this switch to turn the printer power on and off. 16. Ventilators These holes help to keep components inside the printer from overheating. 11. Paper Tray (Tray 1) Loads up to 500
  • Ricoh AP610N | Setup Guide - Page 17
    , replace this unit. 2. Front Cover Open this cover when accessing the inside of the printer. 3. Guide Board Open this board to remove misfed paper. 4. Registration Roller Feeds the paper. If it becomes dirty, clean it. See "Cleaning the Registration Roller", Maintenance Guide. AGN044S 5. Transfer
  • Ricoh AP610N | Setup Guide - Page 18
    Panel 1 1. Display Shows the current status of the printer and error messages. See "Error & Status Messages on the Control Panel", Maintenance Guide. 2. Power indicator Is on while the printer power is on. Is off when the power is turned off or while the printer is in Energy Saver mode. 3. Alert
  • Ricoh AP610N | Setup Guide - Page 19
    this key to clear some errors. See "Troubleshooting", Maintenance Guide. 11. {U} {T} keys Use these keys to increase or decrease values on the display when making settings. Keep the key pressed to quicken scrolling, and increase or decrease values on the display in units of 10. Control Panel 1 15
  • Ricoh AP610N | Setup Guide - Page 20
    Guide to the Printer 1 16
  • Ricoh AP610N | Setup Guide - Page 21
    The printer's location should be carefully chosen because environmental conditions greatly affect its performance. R WARNING: • Confirm the wall outlet is near the machine and freely accessible, so that in the event of emergency, it can be unplugged easily. • Only connect the machine to the power
  • Ricoh AP610N | Setup Guide - Page 22
    Installation Leave enough space around the printer. This space is necessary to operate the printer. The recommended (or minimum) space requirements are as follows: 2 ZKGH010E A: 10 cm (4 inches) or more B: 10 cm (4 inches) or more C: 100 cm (39.4 inches) or more D: 10 cm (4 inches) or more ❖ Optimum
  • Ricoh AP610N | Setup Guide - Page 23
    that are excessively cold, hot, or humid ❒ Locations near air conditioners or humidifiers ❒ Locations near other electronic equipment ❒ Locations subject to frequent strong vibration ❖ Power Source Connect the power cable to a power source of the following specification: • 220 - 240 V, 50/60 Hz
  • Ricoh AP610N | Setup Guide - Page 24
    for your computer. ❖ Manuals and CD-ROMs Setup Guide (This manual) Maintenance Guide CD-ROM "Printer Drivers and Utilities" CD-ROM "Display-Version Manuals (HTML)" CD-ROM "Print-Version Manuals (PDF)" ❖ Parts Power Cable Paper Tray Cover AGN100S Additional Documentation B Remove the plastic bag
  • Ricoh AP610N | Setup Guide - Page 25
    . Note ❒ The toner cartridges that comes with the printer will allow you to print up to about 3,000 pages. These numbers were obtained from printing A4 K5% charts, but the actual number of pages will vary depending on the paper type, size, contents, and settings. ❒ Toner cartridges (consumable) are
  • Ricoh AP610N | Setup Guide - Page 26
    ZKGT151E Important ❒ Be sure to remove the tape com- pletely before installing the toner cartridge. Otherwise, the printer might be damaged. ❒ If you pull out the strips when the toner cartridge is slant or standing on its side, the cartridge might cause trouble with the printer. ❒ Be sure to pull
  • Ricoh AP610N | Setup Guide - Page 27
    Important ❒ Do not close the front cover with force. If you cannot close the cover easily, pull out the toner cartridge from the printer and insert it again. After that, close the front cover again. ❒ Dispose of removed fixing material and tape in the same manner as ordinary plastic waste. 23
  • Ricoh AP610N | Setup Guide - Page 28
    how to load paper into the standard paper tray (Tray 1). C Load the new paper into paper tray with print side up. R CAUTION: • Do not pull out the paper tray 2 forcefully. If you do, the tray might fall and cause an injury. Important ❒ To avoid paper jams, make sure paper is not stacked
  • Ricoh AP610N | Setup Guide - Page 29
    the printer might be damaged or a printing problem might occur. ❒ Do not slide the paper tray in and out with force. If you do, the front and side paper guides will move out of the place. Reference For details about usable types of paper, see "Loading Paper", Maintenance Guide. Loading Paper 2 25
  • Ricoh AP610N | Setup Guide - Page 30
    . A Make sure the power is set to "b" Off. AGN034S B Plug in the power cable. Important ❒ Make sure the power cable is plugged securely into the wall outlet. ❒ Turn the power off when plugging and unplugging the power plug. C Turn the power to "a" On. AGN001S The power indicator on the control
  • Ricoh AP610N | Setup Guide - Page 31
    lan- guage will appear on the display. If you want to use the display in English, the following procedures are un- 2 necessary. Note ❒ The default setting is English. A Press the {Menu} key. AGN504S The following message appears on the display: AGN503S The [Menu] screen appears on the display
  • Ricoh AP610N | Setup Guide - Page 32
    message appears on the display. If there is an error message, see "Troubleshooting", Maintenance Guide. D Check the options. Note ❒ For details about the configura- tion page, see "Interpreting the Configuration Page", Software Guide. E Press the {Online} key. AGN505S The initial screen appears
  • Ricoh AP610N | Setup Guide - Page 33
    the specifications of each option, see Maintenance Guide. R CAUTION: • Before installing options, the machine should be turned off and unplugged for at least an hour. Components inside the machine become very hot, and can cause a burn if touched. • Before moving the machine, unplug the power cable
  • Ricoh AP610N | Setup Guide - Page 34
    A Attach the paper feed unit (Paper Feed Unit Type 610). Attach the paper feed unit to the bottom of the printer. You can attach up to two paper feed unit. Up to 1600 sheets of paper can be loaded. B Attach the envelope feeder (Envelope Feeder Type 610). 3 Replace the paper tray of the optional
  • Ricoh AP610N | Setup Guide - Page 35
    Feeder unit can be used in "Tray 2". Neither the main unit's feed tray (Tray 1) nor Tray 3 can be used for this purpose. 3. Duplex Unit AD610 (duplex unit) You can print on both sides of paper. Install the duplex unit by removing the rear cover of the printer. See p.53 "Attaching Duplex Unit AD610
  • Ricoh AP610N | Setup Guide - Page 36
    Hard Disk Drive Type 2600". Note ❒ You can have one of the following types of extension board installed at the same time: 802.11b Interface Unit Type F, 1394 Interface Unit Type 4510, Bluetooth Interface Unit Type C. Reference For the specifications of each option, see Maintenance Guide. 32
  • Ricoh AP610N | Setup Guide - Page 37
    machine to topple. ❒ More than two paper feed units cannot be attached. ❒ Check the printer nameplate to confirm the model code. A Check the package contains the following: ❖ Paper Feed Unit (including a paper tray) ZKGX390E Note ❒ If you attach two paper feed units at the same time, stack them up
  • Ricoh AP610N | Setup Guide - Page 38
    sales or service representative. ZKGX400E E Attach the interface cable to the printer. Reference For printing the configuration page, see p.28 "Test Printing" See "Loading Paper", Maintenance Guide. When adjusting the printing position, see "Adjusting Tray Registration", Maintenance Guide. 34
  • Ricoh AP610N | Setup Guide - Page 39
    beneath the paper tray. Note ❒ Keep the paper tray with paper in a cool dark place. C Lift the front of the envelope feeder, and slide it carefully into the printer until it stops. AGN037S ZKGP340E Reference For information about loading paper, see "Loading Enve- lopes", Maintenance Guide. 35
  • Ricoh AP610N | Setup Guide - Page 40
    The removed screws are re- ❒ Before touching the memory unit, unit, you must make settings in the printer driver. A Turn off the power of the printer, and then unplug the printer's power cable and the interface cable. ZKGX280E D Pull out the handle of the control- ler board. B If the duplex unit
  • Ricoh AP610N | Setup Guide - Page 41
    rail using the "T" mark, and then slide it into the printer slowly until it stops. ZKDX021J H Remove the default memory unit before installing a new memory unit. Press down the levers on both sides to remove the default memory unit. ZKGX250E K Push the handle of the controller board until it
  • Ricoh AP610N | Setup Guide - Page 42
    Installing Options L Fasten the controller board to the printer with the two screws. 3 ZKGX270E M Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. ZKGX243E If the duplex unit is not attached, this step is not
  • Ricoh AP610N | Setup Guide - Page 43
    "SCSI print" ZKDP400J ❖ 1394 Interface Cable (6 pins x 4 pins) • Windows XP, Windows Server 2003 "IP over 1394", "SCSI print" ❒ Under Windows 2000, the 1394 interface unit can only be used with Service Pack 1 or later. The client cannot install the printer driver without using an account that has
  • Ricoh AP610N | Setup Guide - Page 44
    until it stops ( ). E Pull out the handle of the control- ler board. 3 ZKGX370E ZKGX320E If the duplex unit is not attached, go to the following steps. D Remove the two screws holding the controller board in place. F Pull the handle, and then slide the controller board out. Note ❒ Use a coin
  • Ricoh AP610N | Setup Guide - Page 45
    controller board. ❒ The removed cover is not used when installing the 1394 interface unit. 3 ZKGX443E K Match the controller board to the top and bottom rail using the "T" mark, and then slide it into the printer slowly until it stops. ZKGX410E I Attach the 1394 interface unit to the controller
  • Ricoh AP610N | Setup Guide - Page 46
    . 3 ZKGX272E N Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. Note ❒ After finishing installation, you can check the 1394 interface unit is properly installed: Print the configuration page from the "List/Test
  • Ricoh AP610N | Setup Guide - Page 47
    , 3 discharge any static electricity. and then unplug the printer's Static electricity can damage the 802.11b interface unit. power cable and the interface cable. C ❒ Do not subject the 802.11b interface If the duplex unit is attached, unit to physical shocks. push down the lever on right
  • Ricoh AP610N | Setup Guide - Page 48
    These screws are used again in fastening the controller board. fastening the 802.11b interface unit to the controller board. ❒ The removed cover is not used when installing the 802.11b in- 3 terface unit. ZKGX280E E Pull out the handle of the control- ler board. ZKGX410E I Attach the 802.11b
  • Ricoh AP610N | Setup Guide - Page 49
    until it clicks. 3 ZKGX380E ZKGX442E K Insert the card slowly into the in- terface unit with the label facing down and the uneven black antenna surface facing up until it stops. N Fasten the controller board to the printer with the two screws. ZKGX500E L Match the controller board to the top and
  • Ricoh AP610N | Setup Guide - Page 50
    Installing Options P Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. 3 ZKGX243E If the duplex unit is not attached, this step is not necessary. Note ❒ After finishing installation, you can check the 802.11b
  • Ricoh AP610N | Setup Guide - Page 51
    shocks. ZKDP900J A Check the package contains the following: ❖ Bluetooth Interface Unit Type C • Interface Unit B Turn off the power of the printer, and then unplug the printer's power cable and the interface cable. C If the duplex unit is attached, push down the lever on right side ( ) and then
  • Ricoh AP610N | Setup Guide - Page 52
    controller board on a flat surface. Note ❒ Use a coin or similar object if the screws do not turn easily. H Remove the two screws and the cover of the Bluetooth interface unit mounting bracket. ❒ These screws are used again in fastening the controller board. Note ❒ These screws are used again in
  • Ricoh AP610N | Setup Guide - Page 53
    L Match the controller board to the top and bottom rail using the "T" mark, and then slide it into the printer slowly until it stops. ZKGX431E J Fasten the network interface unit to the controller board with the two screws. ZKGX601E M Push back the handle of the con- troller board until it
  • Ricoh AP610N | Setup Guide - Page 54
    Installing Options N Fasten the controller board to the printer with the two screws. Q Align the power cable to the left side groove of the duplex unit, and then slide the duplex unit in until it is connected to the printer. 3 ZKGX602E O Press the antenna to extend it. ZKGX603E P Attach the
  • Ricoh AP610N | Setup Guide - Page 55
    ZKGX151E E Fasten the two screws (using a coin, etc.) to fix the hard disk drive. ZKDX220J B Turn off the power of the printer, and then unplug the power cable. C Remove the two screws and the cover of the hard disk drive mounting bracket. Note ❒ Use a coin or similar object if the screws do not
  • Ricoh AP610N | Setup Guide - Page 56
    . Fasten the screw to secure the cover. AET104S B Turn off the power of the printer, and then unplug the power cable. C Remove the card slot cover at the back of the printer. AGN012S Note ❒ Do not touch the network data protection unit while the machine is in use. It may come loose, even if pushed
  • Ricoh AP610N | Setup Guide - Page 57
    nameplate to confirm the model code. A Check the package contains the 3 following: ❖ Duplex Unit AGN004S E Remove the rear cover in the hor- izontal direction. AGN036S B Turn off the power of the printer, and then unplug the power cable. C Remove the adhesive tapes. ZKGX220E Note ❒ The
  • Ricoh AP610N | Setup Guide - Page 58
    your sales or service representative. ❒ If the printing position is not correct, adjust the registration of the trays. For more information about adjusting the registration of the trays, see "Adjusting Tray Registration", Maintenance Guide. Reference For printing the configuration page, see p.28
  • Ricoh AP610N | Setup Guide - Page 59
    below to connect the printer to the computer through the network. Prepare the hub and other network devices before connecting the 10 BASE-T or 100 BASE the end of the cable (on the end closest to the printer). ZKEP320E B Connect the Ethernet cable to the Ethernet port. AGN013S C Connect the other end
  • Ricoh AP610N | Setup Guide - Page 60
    Connecting the Printer -Reading the LED Lamps 1 2 ZKGH260E 1. Green: lit when the printer is properly connected to the network. 4 2. Yellow: lit when 100BASE-TX is being used. Unlit when 10BASE-T is being used. 56
  • Ricoh AP610N | Setup Guide - Page 61
    you are using. ❒ USB connection is possible under Windows 98 SE/Me/2000/XP, Windows Server 2003, Mac OS 9.x, and Mac OS X v10.3 or higher. ❒ Windows 98SE/Me supports USB1.1 speeds. ❒ USB connection with Macintosh is only possible via the printer's USB port. A Connect the square-shaped connector of
  • Ricoh AP610N | Setup Guide - Page 62
    Parallel Connection Important ❒ The parallel interface cable is not provided with the printer. ❒ The printer's parallel connection is a standard bidirectional interface that requires an IEEE 1284-compliant 36-pin parallel cable and host computer parallel port. ❒ Use shielded interface cable
  • Ricoh AP610N | Setup Guide - Page 63
    4.5 meters (14.8 feet) long. A Connect the interface cable to the 1394 interface unit. 4 ZKGX550E B Connect the other end to the host computer. Note ❒ You can interface unit can be used. ❒ If you have an interface cable with a ferrite core, connect the ferrite core end to the printer. Reference
  • Ricoh AP610N | Setup Guide - Page 64
    Connecting the Printer 4 60
  • Ricoh AP610N | Setup Guide - Page 65
    Configure the printer for the network using the control panel. ❒ The following table shows the control panel settings and their default are all set automatically. ❒ Make this setting only when it is necessary. See Software Guide. A Press the {Menu} key. AGN503S The [Menu] screen appears on the
  • Ricoh AP610N | Setup Guide - Page 66
    Configuration screen returns to the network setup menu. Note ❒ The default is "Active". ❒ Leave unused protocols "Not Active". use TCP/IP, assign the IP address to the printer. Press the {U} or {T} key to display [IP as the IP address. ❒ The value moves by 10 if the {U} or {T} key is kept pressed.
  • Ricoh AP610N | Setup Guide - Page 67
    : *On Note ❒ "p" shows the current setting. ❒ After default setting ("Auto"). When you first select "Auto", the frame type detected by the printer is adopted. If your network can use more than two frame types, the printer configuration page to con- firm the settings made. Reference For
  • Ricoh AP610N | Setup Guide - Page 68
    11b (Wireless LAN) Configuration Configure the printer to use IEEE 802.11b (Wireless LAN). The following table shows the control panel settings and their default values. These items appear in the [Host Interface] menu. A Press the {Menu} key. Setting Name Default Value Comm. Mode 802.11 Ad hoc
  • Ricoh AP610N | Setup Guide - Page 69
    Configuration E Press the {U} or {T} key to select the transmission mode of IEEE 802.11b, and then press the {# Enter} key. Comm. Mode: *802.11 Ad hoc After the settings are made, about two seconds later, the screen returns to the IEEE 802.11b setting menu. Note ❒ The factory default Software Guide.
  • Ricoh AP610N | Setup Guide - Page 70
    Configuration M Press the {U} or {T} key to select characters, and then press the {# Enter} key. Q Press the {U} or {T} key to dis- play [ inputting an ASCII WEP key. Then press the {# Enter} key. WEP Key: k [ 0] The value in brackets at the upper right is the number of characters entered. 66
  • Ricoh AP610N | Setup Guide - Page 71
    Note Ready ❒ When using 64 bit WEP, up to W 10 characters can be used for hexadecimal and up to five Print a configuration page to con- 5 The number of characters that Reference For details about printing the configuration page, see p.28 "Test Printing". can be entered is limited to 10 or 26
  • Ricoh AP610N | Setup Guide - Page 72
    Use this procedure to configure the printer for use in an IEEE 1394 environment. The following table shows the control panel settings and their default values. These items appear in the [Host Interface] menu. IP over 1394 A Press the {Menu} key. Setting Name Value DHCP On IP Address1394
  • Ricoh AP610N | Setup Guide - Page 73
    Note ❒ The value moves by 10 if the {U} or {T} key reset. ❒ Do not set "011.022.033.044" as the IP address. ❒ To get the IP address for the printer configuration page to con- firm the settings made. Reference For printing the configuration page, see "Printing a Configuration Page", Software Guide
  • Ricoh AP610N | Setup Guide - Page 74
    to con- firm the settings made. Reference For details about printing the configuration page, see p.28 "Test Printing". The IEEE 1394 setting menu appears. D Set [SCSI print] and [Bidi-SCSI print] if necessary. Note ❒ The default setting is "Active". E Press the {U} or {T} key to dis- play [SCSI
  • Ricoh AP610N | Setup Guide - Page 75
    Using Quick Install, the PCL printer driver and RPCS printer driver and SmartDeviceMonitor for Client is installed under network environment, and TCP/IP port will be set. Important ❒ To install printer driver under Windows 2000/XP Professional, Windows Server 2003, and Windows NT 4.0, you must have
  • Ricoh AP610N | Setup Guide - Page 76
    printer whose printer port is displayed in [Connect To]. G Click [Install]. The printer driver installation computer, and then reinstall the other software or printer drivers. ❒ Auto Run may not work with certain unless bidirectional communication between the printer and computer is enabled via
  • Ricoh AP610N | Setup Guide - Page 77
    root directory to your hard disk drive, and then launch "Setup.exe" to start the installation. ❒ To uninstall the Operating Instructions Manual, select [Programs] in the [Start] menu, select your printer driver, and then click [Uninstall]. You can uninstall each Manual Guide separately. ❒ If you are
  • Ricoh AP610N | Setup Guide - Page 78
    610, 35 Ethernet, 55, 61 Ethernet Port, 55 G Guide to the Printer Control Panel, 14 Exterior, 11 Inside, 13 H Hard Disk Drive, 51 I Installing Options, 29 Installing the Printer Driver, 71 Install the Operating Instructions, 73 IP Address, 61 L Loading Paper, 24 M Memory Unit (SDRAM module), 36 74
  • Ricoh AP610N | Setup Guide - Page 79
    Data Protection Unit, 52 O Option Installation Flow Chart, 30 P Paper Feed Unit Type 610, 33 Q Quick Install, 71 S Safety Information, 2 Setting Up, 17 T Test Printing, 28 Toner Cartridge, 21 Tray 1, 24 Turning the Power On, 26 U Unpacking, 20 USB Port, 57 W Where to Put the Printer, 17 Wireless
  • Ricoh AP610N | Setup Guide - Page 80
    MEMO 76
  • Ricoh AP610N | Setup Guide - Page 81
    MEMO 77
  • Ricoh AP610N | Setup Guide - Page 82
    MEMO 78 GB GB G116-8600A
  • Ricoh AP610N | Setup Guide - Page 83
    POWER OFF. Declaration of Conformity "The Product complies with the requirements of the EMC Directive 89/336/EEC and its amending directives and the Low Voltage Directive 73/23/EEC and its amending directives." Declaration of Conformity Notice to Users in EEA Countries 802.11b Interface Unit Type
  • Ricoh AP610N | Setup Guide - Page 84
    Plaza, No.222 Huai Hai Zhong Road, Lu Wan District, Shanghai P.C.:200021 Phone: +86-21-5396-6888 Singapore RICOH ASIA PACIFIC PTE.LTD. 260 Orchard Road, #15-01/02 The Heeren, Singapore 238855 Phone: +65-6830-5888 Model number: Aficio AP610N Printed in the Netherlands GB GB G116-8600A G1168600A
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Setup Guide
Read this manual carefully before you use this product and keep it handy for future reference. For safe and correct use, please be sure to read
the Safety Information in this manual before using the machine.
Guide to the Printer
Setting Up
Installing Options
Connecting the Printer
Configuration
Installing the Printer Driver
1
2
3
4
5
6