Ryobi ACRM009 Operation Manual

Ryobi ACRM009 Manual

Get Ryobi ACRM009 PDF manuals and user guides View all Ryobi ACRM009 manuals
Add to My Manuals
Save this manual to your list of manuals

Ryobi ACRM009 manual content summary:

  • Ryobi ACRM009 | Operation Manual - Page 1
    LAWN MOWER WARNING: To reduce the risk of injury, user must read and understand the operator's manual for their riding lawn mower before using this accessory. Save these instructions. Refer to them frequently and use them to instruct other users. If you loan someone this product, loan them these
  • Ryobi ACRM009 | Operation Manual - Page 2
     Wedge a block of wood between the blade and mower deck to prevent the blade from turning.  Loosen the blade nut by turning it counterclockwise (as viewed from bottom of mower) using a 15 mm wrench or socket (not provided).  Remove the blade nut, spacer, blade insulator, and blade.  Place the
  • Ryobi ACRM009 | Operation Manual - Page 3
    . Les consulter fréquemment et les utiliser pour instruire les autres utilisateurs. Si cet produit est prêté, il doit être accompagné de ces instructions. CÂBLE Les lames de rechange ACRM009 et ACRM010 est compatible avec les tondeuses Ryobi® qui ont un 30 po. plateau de coupe. Le jeu de
  • Ryobi ACRM009 | Operation Manual - Page 4
     Mettez une pièce de bois entre la lame et le châssis de la tondeuse pour empêcher la lame de tourner.  Desserrez l'écrou de la lame en le tournant dans le sens antihoraire (par rapport au bas de la tondeuse) en utilisant une clé de 15 mm ou une douille (non fournies).  Enlevez l'écrou de lame,
  • Ryobi ACRM009 | Operation Manual - Page 5
    base de corte 30 pulg. Las cuchillas combinadas y las cuchillas para embolsadora se venden por separado. Las cuchillas combinadas se muestran en este manual únicamente con fines ilustrativos. Sin embargo, las cuchillas para embolsadora se pueden instalar de la misma forma. EXTRACCIÓN DE LA BASE DE
  • Ryobi ACRM009 | Operation Manual - Page 6
    ADVERTENCIA: Si levanta la podadora para acceder las cuchillas, asegúrese de que la podadora se encuentre asegurada correctamente y el freno de estacionamiento esté colocado antes de proceder. Si no asegura la podadora correctamente puede provocar una caída, lo que podría causar la muerte o posibles
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
Fig. 1
HITCH PIN
WASHER
CABLE
CUTTING
DECK
REPLACEMENT BLADES
FOR USE WITH RYOBI
®
30 in. ELECTRIC RIDING LAWN MOWER
WARNING:
To reduce the risk of injury, user must read and understand
the operator’s manual for their riding lawn mower before
using this accessory. Save these instructions. Refer to them
frequently and use them to instruct other users. If you loan
someone this product, loan them these instructions also.
The ACRM009 and ACRM010 replacement blades are com-
patible with Ryobi® mowers that have a 30 inch deck. Combo
blades and bagging blades are sold separately. For purposes of
the illustrations in this manual, only combo blades are shown.
However, bagging blades would install in the same way.
REMOVING THE CUTTING DECK
See Figure 1.
If desired, the cutting deck can be removed from the mower to
make accessing the blades easier when changing.
Make sure blade engage knob is down.
Stop the motor, remove the start key, and set the parking
brake.
Disconnect the cables that connect the cutting deck to the
mower.
Lower the cutting deck to its lowest position.
Remove the 4 hitch pins and washers that secure the cutting
deck in place.
Slide the deck out from under the mower.
Reverse the process to reattach the cutting deck to the
mower.
INSTALLING BLADES
See Figures 2 - 4.
CAUTION:
Only use replacement blade bolts authorized by the
manufacturer of your riding mower. Use of blade bolts not
authorized is hazardous and may damage your riding mower.
Make sure blade engage knob is down.
Stop the motor, remove the start key, and set the parking
brake.
Raise the height of the cutting deck to its highest position
to allow access to blades.
NOTE:
If necessary, raise the mower by placing on a lift
or using a jack and jack stands, or remove the cutting
deck as described in the previous section to gain access
to the blades.
WARNING:
If raising the mower to access the blades, make sure the
mower is properly secured and the parking brake is set
before proceeding. Failure to properly secure the mower
could cause it to fall, resulting in death or possible serious
personal injury.
Fig. 2
BLOCK OF WOOD
BLADE
WRENCH
ACRM010 BAGGER BLADES
ACRM009 COMBO BLADES