Ryobi P213 English Manual

Ryobi P213 Manual

Get Ryobi P213 PDF manuals and user guides View all Ryobi P213 manuals
Add to My Manuals
Save this manual to your list of manuals

Ryobi P213 manual content summary:

  • Ryobi P213 | English Manual - Page 1
    OPERATOR'S MANUAL 10 in. DRILL PRESS DP102l Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and ­operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of
  • Ryobi P213 | English Manual - Page 2
    ...8  Glossary of Terms...9  Features...10-11  Tools Needed...11  Loose Parts...12  Assembly...13-17  Operation...18-20  Adjustments...21-22  Maintenance...23  Troubleshooting...24  Parts Ordering / Service...Back Page INTRODUCTION This tool has many features for making its use more
  • Ryobi P213 | English Manual - Page 3
    Follow instructions for lubricating and changing accessories.  DISCONNECT TOOLS. When not in use, before servicing, manual for recommended accessories. The use of improper accessories may result in injury.  NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped.  CHECK DAMAGED PARTS
  • Ryobi P213 | English Manual - Page 4
    .  WHEN SERVICING use only identical replacement parts. Use of any other parts may create a hazard or cause product damage.  USE ONLY RECOMMENDED ACCESSORIES listed in this manual or addendums. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe
  • Ryobi P213 | English Manual - Page 5
    or by an authorized service center to avoid risk.  SAVE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this tool, loan them these instructions also. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction
  • Ryobi P213 | English Manual - Page 6
    minute Wet Conditions Alert Do not expose to rain or use in damp locations. Read The Operator's Manual To reduce the risk of injury, user must read and understand operator's manual before using this product. Eye Protection Safety Alert No Hands Symbol Hot Surface Always wear safety goggles or
  • Ryobi P213 | English Manual - Page 7
    servicing, use only identical replacement parts. WARNING: To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator's manual. Save this operator's manual and review frequently for continuing safe operation and instructing
  • Ryobi P213 | English Manual - Page 8
    distance. A line that can support one power tool may not be able to support two or three tools. Grounding Instructions In the event of a malfunction a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as
  • Ryobi P213 | English Manual - Page 9
    A cut removing a wedge from a block so the end (or part of the end) is angled rather than at 90°. Compound Cut A drill presses) A small hole drilled in a workpiece that serves as a guide for drilling blades when the workpiece is not properly supported. Through Sawing Any cutting operation where the
  • Ryobi P213 | English Manual - Page 10
    FEATURES product specifications Chuck 1/2 in. Input 120 Volt, 60Hz, AC Only, 3 Amps Motor 1/4 HP Induction No Load Speed 570-3,050 r/min. (RPM) Swing 10 in. Spindle Travel 2-3/8 in. Table Size 9-1/4 in. x 8-3/16 in. Table Movement 45° bevel, 360° swivel Overall Height 29 in. Net Weight
  • Ryobi P213 | English Manual - Page 11
    45˚ for angle drilling. worklight The integrated worklight can be used to help illuminate the work area. It requires a 15-watt, 120-volt, candelabra-base bulb (not included). TOOLS NEEDED The following tools (not included) are needed for assembly and alignment: mallet or hammer adjustable wrench
  • Ryobi P213 | English Manual - Page 12
    the drill press: Head Assembly 1 Column Assembly 1 Table Assembly 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Table Adjustment Handle 1 Table Lock Handle 1 AA Batteries 2 Chuck 1 Chuck Key 1 Worm Gear 1 Operator's Manual (not shown 1 aa batteries chuck
  • Ryobi P213 | English Manual - Page 13
    are damaged or missing, please call 1-800-525-2579 for assistance. WARNING: If any parts are damaged or missing do not operate this tool until the missing parts are replaced. Failure to heed this warning could result in possible serious personal injury. attaching column assembly to base See Figure
  • Ryobi P213 | English Manual - Page 14
    assembly installing table assembly See Figures 6 - 8. ■ Loosen the set screw in the column collar. Remove the column collar and gear rack from the column and set aside.  Locate the worm gear and feed the D-shaft through the hole in the table assembly.  Install table adjustment handle over the
  • Ryobi P213 | English Manual - Page 15
    be fully opened to avoid damaging jaws.  Using a piece of scrap wood to protect the chuck, firmly tap the chuck into place using a mallet or hammer.  Position the head assembly onto the column with the chuck positioned over the table. Note: This tool is heavy. Get help when needed. feed handle
  • Ryobi P213 | English Manual - Page 16
    cover.  Close head assembly cover. battery compartment cover AA Batteries WARNING: Use of controls or adjustments or performance of procedures other than those specified herein could result in hazardous radiation exposure. Mounting the Drill press See Figure 14. If the drill press is to be used
  • Ryobi P213 | English Manual - Page 17
    the intersection of the laser lines is precisely at the spot where the drill bit meets the workpiece. If it is not, the laser lines should head assembly.  Mark an "X" on a piece of scrap wood.  Insert a small drill bit into the chuck and align its tip to the intersection of the lines of the "X".
  • Ryobi P213 | English Manual - Page 18
    PRESS OFF:  With the switch key inserted into the switch, push the switch down to turn OFF ( O ). TO lock THE DRILL PRESS:  Place the switch in the OFF ( O ) position.  Remove the switch key from the switch and store in a secure location. WARNING: Always remove the switch
  • Ryobi P213 | English Manual - Page 19
    the table lock handle.  Rotate the table to the desired position.  Retighten the table lock handle installing and removing bits See Figure 19. ■ Unplug the drill press.  Open or close the chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use.  Insert
  • Ryobi P213 | English Manual - Page 20
    bit based on the hole size desired. For large holes, drill a pilot hole first, using a smaller diameter bit.  Select and set the recommended spindle speed. Refer to Changing Speeds in the Adjustments section of this manual.  Set table assembly to desired height. Refer to Adjusting Table Height
  • Ryobi P213 | English Manual - Page 21
    table to the desired ­angle.  Retighten the hex bolt securely. adjusting depth GAUGE See Figure 23. Adjust the depth gauge when you need to drill a number of holes to exactly the same depth.  Loosen the lock knob.  Rotate depth gauge to desired setting.  Retighten lock knob securely using the
  • Ryobi P213 | English Manual - Page 22
    the head assembly. The speed chart located on the cover inside the head assembly shows the recommended speed and pulley configuration for each drilling operation. To change the pulley configuration:  Lift head assembly cover from front to open.  Loosen the tension bolt.  Remove the drive belt
  • Ryobi P213 | English Manual - Page 23
    MAINTENANCE WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or and to help prolong the life of the drill press. batteries Check the laser batteries regularly to avoid deterioration. Remove the batteries if you will not be using the laser
  • Ryobi P213 | English Manual - Page 24
    troubleshooting Problem Noisy operation Bit burns or smokes Excessive drill runout or wobble Drill bit binds in workpiece Workpiece support the Adjustments section of this manual. Retract bit frequently to clear chips. Sharpen or replace bit. Feed fast enough; allow drill to cut. Lubricate bit for
  • Ryobi P213 | English Manual - Page 25
    NOTES 25
  • Ryobi P213 | English Manual - Page 26
    OPERATOR'S MANUAL 10 in. DRILL PRESS DP102l • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
OPERATOR’S MANUAL
10 in. DRILL PRESS
DP102L