Samsung DV50K7500GW/A3 User Manual - Page 25

Using the short hose as an extension, short hose B, Y connector A, water, hoses C

Get Samsung DV50K7500GW/A3 PDF manuals and user guides View all Samsung DV50K7500GW/A3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Installation Using the short hose as an extension B A C 1. Close the cold water tap. If you have a washer cold water hose attached to the cold water faucet, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten. You can damage the coupling. 3. Connect the Y connector (A) to the brass male end of the short hose. Turn the coupling by hand until it is tight. 4. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten. You can damage the coupling. 5. Connect the angled end of the water hoses (C) to the filling valve at the bottom rear of the dryer. Turn the coupling by hand until it is tight. 6. Using pliers, tighten the coupling an additional two-thirds turn. Do not overtighten. You can damage the coupling. 7. If you detached the cold water hose from your washer, attach the hose to the free end of the Y connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn. 8. Open the cold water tap, and then check for any leaks. DV7500K-03381C-02_EN.indd 25 English 25 4/7/2016 5:05:46 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
Installation
English
25
Using the short hose as an extension
B
A
C
1.
Close the cold water tap. If you have
a washer cold water hose attached to
the cold water faucet, unscrew and
remove the hose. Then, connect the
short hose (B)
to the cold water tap.
Turn the coupling by hand until it is
tight.
2.
Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten. You can damage the
coupling.
3.
Connect the
Y connector (A)
to the
brass male end of the short hose. Turn
the coupling by hand until it is tight.
4.
Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten. You can damage the
coupling.
5.
Connect the angled end of the
water
hoses (C)
to the filling valve at the
bottom rear of the dryer. Turn the
coupling by hand until it is tight.
6.
Using pliers, tighten the coupling an
additional two-thirds turn. Do not
overtighten. You can damage the
coupling.
7.
If you detached the cold water hose
from your washer, attach the hose
to the free end of the Y connector,
tighten the coupling by hand until it is
tight, and then, using a pliers, tighten
an additional two-thirds turn.
8.
Open the cold water tap, and then
check for any leaks.
DV7500K-03381C-02_EN.indd
25
4/7/2016
5:05:46 PM