Samsung MC12J8035C Installation Guide - Page 2

BEFORE YOU BEGIN, Parts included in the kits, Tools needed

Get Samsung MC12J8035C PDF manuals and user guides View all Samsung MC12J8035C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector's use. - Observe all governing codes and coordinates. - B e sure to disconnect the plug of the microwave oven from the electrical outlet before installing the Builtin Kit. Remove the turntable from the oven cavity. - The kit includes metal parts, due caution should be used in handling and installation to avoid the possibility of injury. - D o not remove permanently affixed labels, warnings or plates from the product. Doing so may void the warranty. Warning - The electrical requirements for this oven are 115-120 volts AC, 15 amps or larger. MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd 5-8 Parts included in the kits Trim Frame (1 EA) Duct Base (1 EA) Duct Side (1 EA) Side Bracket (2 EA) Screw A (5/8" length) (6 EA) Screw B (15/32" length) (2 EA) Screw C (25/64" length) (2 EA) Template (1 EA) Tools needed Screwdriver Pencil Drill with 7/64 or #35 Drill bit Scissors Tape measure Installation STEP 1 Width Depth 3" min Electric Heat Source Model High CUTOUT DIMENSIONS Height Width Depth 18 3/4" ± 1/16" 24" ± 1/16" 21 1/2" ± 1/16" WARNING To avoid risk of electrical shock, personal injury, or death: -Before drilling into the wall, note where electrical outlets are and where electrical wire might be concealed behind the wall. YOU COULD GET AN ELECTRICAL SHOCK if you contact electrical wire with the drill bit. -Locate and disconnect the power to any electrical circuits that could be affected by installing this oven. IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRICAL SHOCK. WARNING To avoid personal injury, wear gloves when handling the metal parts. Parts are sharp and can cause cuts and abrasions. STEP 2 After placing the Template to match with cabinet center line mark four Holes at the bottom. P1 P2 P3 P4 P5 P6 P5 A CENTER LINE C A P6 CABINET OPENING B A P1 P2 C B A P3 P4 After placing the Template to match with center line, mark two Holes at the top. Then drill a pilot hole at 6 positions use 7/64 or #35 Drill bit. NOTE You may not be assembled when using the thicker Drill bit. A : 11 9/32" (287 mm) B : 6 57/64" (175 mm) C : 9 23/32" (247 mm) 2015-06-15 �� 11:16:11

  • 1
  • 2
BEFORE YOU BEGIN
Parts included in the kits
Installation
Trim Frame (1 EA)
Duct Base (1 EA)
Duct Side (1 EA)
Side Bracket (2 EA)
Screw A
(5/8" length) (6 EA)
Screw B
(15/32" length)
(2 EA)
Screw C
(25/64" length)
(2 EA)
Template (1 EA)
Screwdriver
Pencil
Drill with 7/64 or #35
Drill bit
Scissors
Tape measure
STEP 1
CUTOUT DIMENSIONS
Height
18 3/4" ± 1/16"
Width
24" ± 1/16"
Depth
21 1/2" ± 1/16"
WARNING
To avoid risk of electrical shock,
personal injury, or death:
-Before drilling into the wall, note
where electrical outlets are and where
electrical wire might be concealed
behind the wall.
YOU COULD GET AN
ELECTRICAL SHOCK if you contact
electrical wire
with the drill bit.
-Locate and disconnect the power to any
electrical circuits that could be affected
by installing this oven.
IF YOU DO NOT DISCONNECT THE
POWER, YOU COULD GET AN ELECTRICAL
SHOCK.
WARNING
To avoid personal injury, wear gloves
when handling the metal parts. Parts are
sharp and can cause cuts and abrasions.
IMPORTANT
- Save these instructions for local inspector's use.
- Observe all governing codes and coordinates.
-
Be sure to disconnect the plug of the microwave oven from the electrical outlet
before installing the Builtin Kit. Remove the turntable from the oven cavity.
-
The kit includes metal parts, due caution should be used in handling and installation
to avoid the possibility of injury.
-
Do not remove permanently affixed labels, warnings or plates from the product.
Doing so may void the warranty.
Warning
- The electrical requirements for this oven are 115-120 volts AC, 15 amps
or larger.
Read these instructions completely and carefully.
STEP 2
After placing the Template to match
with cabinet center line mark four Holes
at the bottom.
After placing the Template to match with
center line, mark two Holes at the top.
Then drill a pilot hole at 6 positions
use
7/64 or #35 Drill bit.
NOTE
You may not be assembled when using
the thicker Drill bit.
A : 11 9/32" (287 mm)
B : 6 57/64" (175 mm)
C : 9 23/32" (247 mm)
Depth
High
3" min
Electric Heat
Source Model
Width
P1
P2
P3
P4
CENTER
LINE
A
A
B
B
C
C
A
A
CABINET
OPENING
P5
P1
P3
P2
P6
P4
P5
P6
Tools needed
(�����)MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd
5-8
2015-06-15
�� 11:16:11