Samsung ME21R7051S Installation Guide - Page 14

C. Outside back exhaust (horizontal duct), C1. Adapting the microwave blower for outside back exhaust

Get Samsung ME21R7051S PDF manuals and user guides View all Samsung ME21R7051S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Step-by-step installation guide C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) C1. ADAPTING THE MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1. Remove and save the screws that hold the Blower Plate to the microwave. Screw 2. Lift up the Blower plate. Blower Motor Back of Microwave Blower Plate Screw 3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. BEFORE: Fan Blade Openings Facing Forward End B End A CAUTION: To avoid breaking or cracking the blower blade, do not touch the blade. Hold the outer case of the blower when you pull it out or put it back in place. 4. Remove Parts "A" with tin snips or pliers. Parts "A" 5. Rotate the blower unit counterclockwise 180 °. Before Rotation After Rotation Back of Microwave Back of Microwave 6. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match the exhaust openings on the rear of the microwave oven. 7. Close the Blower Plate and attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the back top center of the oven. Push in securely until it is in the lower locking tabs. Take care to ensure that the damper hinge is installed so that it is at the top and that the damper swings freely. Adaptor Back of Microwave Guide Blower motor screw Guide Blower plate screw ME21R7051SS_SG_AA_DE68-04577A-01_EN.indd 14 14 2021-03-25 오전 11:32:31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
14
Step-by-step installation guide
C. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C1. ADAPTING THE MICROWAVE BLOWER FOR
OUTSIDE BACK EXHAUST
1
.
Remove and save the screws that hold the Blower
Plate to the microwave.
2
. Lift up the Blower plate.
Screw
Blower Motor
Back of Microwave
Blower Plate Screw
3
.
Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the blower
unit.
BEFORE: Fan Blade
Openings Facing Forward
End B
End A
CAUTION:
To avoid breaking or cracking the blower
blade, do not touch the blade. Hold the outer case of the
blower when you pull it out or put it back in place.
4
. Remove Parts “A” with tin snips or pliers.
Parts “A”
5
. Rotate the blower unit counterclockwise 180 °.
Before Rotation
After Rotation
Back of Microwave
Back of Microwave
6
. Place the blower unit back into the opening.
AFTER: Fan Blade
Openings Facing Back
End B
End A
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings should
match the exhaust openings on the rear of the
microwave oven.
7
. Close the Blower Plate and attach the exhaust
adaptor to the rear of the oven by sliding it into the
guides at the back top center of the oven. Push in
securely until it is in the lower locking tabs. Take care
to ensure that the damper hinge is installed so that it
is at the top and that the damper swings freely.
Guide
Guide
Adaptor
Blower
plate screw
Back of
Microwave
Blower
motor screw
ME21R7051SS_SG_AA_DE68-04577A-01_EN.indd
14
ME21R7051SS_SG_AA_DE68-04577A-01_EN.indd
14
2021-03-25
오전 11:32:31
2021-03-25
오전 11:32:31