Samsung NX58R4311SS/AA Installation Guide - Page 29

Adjusting the oven burner air adjustment shutters

Get Samsung NX58R4311SS/AA PDF manuals and user guides View all Samsung NX58R4311SS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Adjusting the oven burner air adjustment shutters All oven burners have an air adjustment shutter. The purpose of the shutter is to regulate the flow of air to the flames. Properly adjusted flames should burn steadily with approximately 1 in of blue cone. The flames should never extend past the edge of the burner baffles. Even though these are preset at the factory, they should be checked and, if needed, adjusted periodically to ensure efficient operation. Air adjustment shutter Air adjustment shutter To check and adjust the oven burner air adjustment shutters: 1. Open the oven door. 2. Remove the oven racks. 3. Remove the oven floor. 4. Press the Bake pad, then the Start pad. 5. After the oven has lit, visually check the flames coming out of the upper and lower burners. If adjustment is needed, carefully adjust the air adjustment shutters. The shutters are located at the base of the burner manifolds near the back oven wall. To adjust the shutter, loosen the locking screw and rotate the shutter towards the open or closed position as needed. If flames are lifting off the burner ports, gradually reduce the air shutter opening until the flames are stabilized. Locking screw If flames are too yellow and/or too large, gradually increase the air shutter opening until the flames have approximately a 1 in blue cone. NOTE If the range is set up for natural gas, the flames should burn with no yellow tipping. If the range is set up for LP gas, small yellow tips at the end of the cones are normal. After the flames are adjusted properly, shut off the oven, retighten the locking screws, replace the oven bottom and racks, and close the oven door. Locking screw Installation instructions Install_NX58R4311SS_AA_DG68-01153A-02_EN+MES+CFR.indb 29 English 29 2020-06-16 �� 8:30:23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
English 29
Installation instructions
The shutters are located at the base of the burner manifolds near the back oven
wall.
Locking screw
To adjust the shutter, loosen the locking
screw and rotate the shutter towards the
open or closed position as needed. If flames
are lifting off the burner ports, gradually
reduce the air shutter opening until the
flames are stabilized.
If flames are too yellow and/or too large,
gradually increase the air shutter opening
until the flames have approximately a 1 in
blue cone.
NOTE
If the range is set up for natural gas, the
flames should burn with no yellow tipping.
If the range is set up for LP gas, small
yellow tips at the end of the cones are
normal.
Locking screw
After the flames are adjusted properly, shut
off the oven, retighten the locking screws,
replace the oven bottom and racks, and
close the oven door.
Adjusting the oven burner air adjustment shutters
All oven burners have an air adjustment shutter. The purpose of the shutter is
to regulate the flow of air to the flames. Properly adjusted flames should burn
steadily with approximately 1 in of blue cone. The flames should never extend
past the edge of the burner baffles. Even though these are preset at the factory,
they should be checked and, if needed, adjusted periodically to ensure efficient
operation.
Air adjustment
shutter
Air adjustment
shutter
To check and adjust the oven burner air adjustment shutters:
1.
Open the oven door.
2.
Remove the oven racks.
3.
Remove the oven floor.
4.
Press the
Bake
pad, then the
Start
pad.
5.
After the oven has lit, visually check the flames coming out of the upper and
lower burners. If adjustment is needed, carefully adjust the air adjustment
shutters.
Install_NX58R4311SS_AA_DG68-01153A-02_EN+MES+CFR.indb
29
2020-06-16
�� 8:30:23