Samsung NX58R9421SG/AA Installation Guide - Page 24

Step 8. Check the ignition of surface burners, English, To turn on a surface burner

Get Samsung NX58R9421SG/AA PDF manuals and user guides View all Samsung NX58R9421SG/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Installation instructions Step 8. Check the ignition of surface burners Check the operation of all cooktop and oven burners after the range has been installed and assembled, gas supply lines have been carefully checked for leaks, and electrical power cord has been plugged in. All surface and oven burners have electronic ignition. To turn on a surface burner: 1. Push in and turn the control knob for that 2 surface burner to the Lite position. The "clicking" sound indicates the electronic ignition system is operating properly. The 1 burner will light in about 4 seconds, after the air has been purged from the supply line. 2. After the burner lights, turn the control knob to the desired setting. The "clicking" sound will stop and the flame height will change from Max. to Min. during turning the control knob. 3. Repeat steps 1 and 2 to check the operation of each surface burner in succession. NOTE Place food in the oven after preheating if the recipe calls for it. Preheating is important for good baking results. After the oven has reached the desired cooking temperature, it will beep 6 times. To start the bake burners 01 02 03 04 1. Press the Bake, Roast, or Bake pad. 2. If necessary, use the number pad to change the default temperature (350 °F). You can set the oven to any temperature from 175 °F to 550 °F. 3. Press the START/SET pad. • The gas oven preheats until it reaches the temperature you set. • When preheating is complete, place the food in the gas oven, and then close the door. 4. When cooking is complete, press the OFF/CLEAR pad, and then take out the food. To start the broil burners 03 02 07 1. Put food on a broiling grid in a broiling pan, and then place the pan on the desired rack. 2. Press the Broil pad once for high temperature broiling or twice for low. 3. Press the START/SET pad to start cooking. 4. Let the oven pre-heat for 5 minutes. 5. Place the pan on the desired rack, and then close the oven door. 24 English Installation instructions Install_NX58M9420SS_DG68-00906A-03_EN+MES+CFR.indb 24 10/24/2018 12:51:44 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
24 English
Installation instructions
Installation instructions
Step 8. Check the ignition of surface burners
Check the operation of all cooktop and oven burners after the range has been
installed and assembled, gas supply lines have been carefully checked for leaks,
and electrical power cord has been plugged in.
All surface and oven burners have electronic ignition.
2
1
To turn on a surface burner:
1.
Push in and turn the control knob for that
surface burner to the Lite position. The
“clicking” sound indicates the electronic
ignition system is operating properly. The
burner will light in about 4 seconds, after
the air has been purged from the supply
line.
2.
After the burner lights, turn the control
knob to the desired setting. The “clicking”
sound will stop and the flame height will
change from Max. to Min. during turning
the control knob.
3.
Repeat steps 1 and 2 to check the
operation of each surface burner in
succession.
NOTE
Place food in the oven after preheating
if the recipe calls for it. Preheating is
important for good baking results. After
the oven has reached the desired cooking
temperature, it will beep 6 times.
To start the bake burners
02
03
04
01
1.
Press the
Bake
,
Roast
, or
Bake
pad.
2.
If necessary, use the number pad to change the default temperature (350 °F).
You can set the oven to any temperature from 175 °F to 550 °F.
3.
Press the
START/SET
pad.
•
The gas oven preheats until it reaches the temperature you set.
•
When preheating is complete, place the food in the gas oven, and then close
the door.
4.
When cooking is complete, press the
OFF/CLEAR
pad, and then take out the
food.
To start the broil burners
03
07
02
1.
Put food on a broiling grid in a broiling pan, and then place the pan on the
desired rack.
2.
Press the
Broil
pad once for high temperature broiling or twice for low.
3.
Press the
START/SET
pad to start cooking.
4.
Let the oven pre-heat for 5 minutes.
5.
Place the pan on the desired rack, and then close the oven door.
Install_NX58M9420SS_DG68-00906A-03_EN+MES+CFR.indb
24
10/24/2018
12:51:44 PM