Samsung RF28HFEDBBC Quick Guide Ver.1.0 (English, French, Spanish) - Page 1
Samsung RF28HFEDBBC Manual
View all Samsung RF28HFEDBBC manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Before calling service If you have further questions or your refrigerator has damaged accessory parts, contact us at 1-800-SAMSUNG (726-7864). 1. Automatic Ice Maker does not work • Allow your refrigerator to operate and cool down for 24 hours (1 full day) before dispensing large quantities of ice. 12 9 3 6 • To fill the ice bucket to maximum capacity, dispense a few cubes 8 and 16 hours after installation. • If ICE OFF is lit, the ice maker will not make ice. • To activate the ice maker, press ICE OFF or the Ice Maker Off button on the control panel so it is no longer lit. 2. Slow Ice Production • Check if the ice bucket is completely inserted. • Freezer temp may not be low enough. Set it to -2 °F (-19 °C) or lower. 3. Small ice cubes, ice cubes with bubbles, or slow water dispensing • If the water filter is clogged, the ice make may produce small ice cubes or ice cubes with bubbles. • Replace the water filter cartridge with a new one. 4. Water filter replacement 1. Shut off the water supply, and then press the water dispenser paddle with a glass to relieve any excess pressure. 2. Turn the old water filter about 1/4 turn, counter- clockwise. 3. Pull the old water filter out of the filter case. 4. Insert the new filter into the filter case. 5. Push the filter, and then turn it clockwise until it locks. Make sure to align the mark on the filter with the indicator mark on the filter case. 6. Touch the "Alarm/hold for 3 sec for Filter Reset" button for about 3 seconds to reset the water filter indicator. - If you have trouble inserting the water filter because of high water pressure, shut off the water supply valve. For details, see "Changing the Water Filter" in the User Manual. After installation or when replacing the water filter, dispense at least 1 gallon (2~3 minutes) of water to remove trapped PUSH air from the water line. Otherwise, water may drip from the dispenser after you dispense water. 5. Water is not cool enough • The first glass of water may not be cold enough because the stored water in the water tank has not cooled completely. Dispense several glasses of water and then it would be cool. 6. Water dispenser dripping • If the water line is not inserted into the coupler properly, air could penetrate into the water line causing water to drip from the water dispenser. • CAUTION : Insert the water line into the coupler completely and slide in the clip at the end of the coupler. Red Clip (1/4") Cabinet Tube Dispenser Door Tube 1. The Water Line must be fully inserted to the center of the transparent coupler (Type A) or the Guide Lines (Type B) to prevent water leakage from the dispenser. 2. Insert the from the install pack and confirm that it holds the line firmly. Type A Type B Dispenser Center of Transparent coupler clip A (1/4") (6.35 mm) The Guide Lines clip A (1/4") (6.35 mm) 7. Fridge or freezer Compartments are warm • A llow your refrigerator to operate and cool down for 24 hours (1 full day) to reach the temperature you set. • Also, when you put room temperature or warmer food into your refrigerator, it may need an additional 24 hours to reach the set temperature. 8. Moisture forms on outside/inside of refrigerator • Wipe off the condensation with a dry towel (This may occur during hot and humid weather.) • If the condensation appears on the doors, turn off the Energy Saving function. • If you open the doors frequently or for too long, it may cause moisture to form inside the fridge. 9. Noise Clicks, Pops, Cracks, Snaps • You may hear these noises occasionally from inside the refrigerator. This is normal. These sounds occur when various items contract or expand while temperatures inside the fridge are changing, especially during defrosting. You may also hear these noises when electronic devices, including the ice maker, are operating. 10. Display • Recommended Temp Settings : 0 °F (-18 °C) for freezer and 37 °F (3 °C) for refrigerator. • Filter indicator : The filter Indicator turns red If you dispense about 300 gallons of water or about 6 months has passed. Reset the indicator after replacing the filter by holding the "Alarm/ Hold 3 sec for Filter Reset" button for 3 seconds. The indicator will turn blue. • Ice off : Press the " Ice Off or Ice Maker Off " button to turn the ice making function off. • Cooling Off (Show Room) mode : If the Display shows "0F 0F" (or OFF) code, it means that the Cooling Off function is activated and the refrigerator is not cooling. To cancel the Cooling Off mode, press the two buttons listed for your model in the table below simultaneously for 5 seconds. Model Button RF323** / RF31FM** / RF24FS** Energy Saver + Freezer RF32FMQ** CoolSelect + Freezer RF23H** / RF25H** / RF28H** Freezer + Alarm 11. Food stored in refrigerator is frozen • If food with too much moisture is stored near the cooling vents, it may get frozen. Be sure to keep moist food away from the cooling vents. 12. Moving the Refrigerator • When moving the refrigerator, pull or push it straight forwards or back. Do not wiggle it from side to side. 13. Leveling & Door Alignment • For details, refer to "Leveling the Refrigerator" in the User Manual. • Insert a flat-blade screwdriver into a slot on the control lever, turn it clockwise or counter-clockwise to level the refrigerator. Control Lever Flat-blade screw driver(-) Type A • Open the freezer drawer to gain an access to the adjustable hinge pin. Next, adjust the refrigerator door using the provided 0.16 inch allen wrench. • Insert the provided snap rings. (on some models) RAISE Keep the snap rings out of reach of children. CAUTION Type B ("RF32FMQ**" model only) • Adjust the door height difference by inserting a Snap Ring (1) as shown between the door and the hinge. Insert one snap ring only of the correct thickness. (1) Keep the snap rings out of reach of children. CAUTION 14. Auto Closing Hinge (on some models) • If the Auto Closing door does not close correctly, open the door more than 90°, and then remove the door by lifting it from the Middle Hinge. • Note : Due to its design features, you can only disassemble and reassemble the door when the door is open. (The holes in the Door Shaft and the Door Middle Hinge are deliberately tilted at specific angles so that it is difficult to disassemble and reassemble the door when the door is closed. Door Middle Hinge Auto Closing Pin Out of Alignment Door Bottom • To realign the Auto Closing Hinge: 1. After you have removed the door, use a Philips head screwdriver to remove the screw (1) connecting the hinge to the refrigerator. 2. Using a 3/16" (0.2) Hex wrench, remove the 2 flat head screws (2) connecting the hinge to the refrigerator. Remove the hinge. 3. Using the Door Middle Hinge, rotate the pin on the bottom of the door 90o so that the flat part of the pin is parallel to the side of the door. Remove the hinge from the pin. 4. Re-attach the Door Middle Hinge to the refrigerator. 5. Re-attach the door to the refrigerator. When you reattach the door, make sure you attach it at an angle greater than 90 °. Detach Door Middle Hinge (1) (2) Rotate pin with hinge. Allen wrench Do not use a flat head screwdriver to align the CAUTION Auto close Hinge. It may get damaged. Use the Door middle Hinge instead. ENGLISH DA99-04022A-10.indd 1 13. 11. 5. �� 5:17