Samsung RS277ACBP/XAA User Manual (ENGLISH) - Page 27

Installation Of The Water Dispenser Line

Get Samsung RS277ACBP/XAA PDF manuals and user guides View all Samsung RS277ACBP/XAA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

INSTALLATION OF THE WATER DISPENSER LINE Connecting to water supply line - Shut off the main water supply line and turn the Ice maker to the off position. - Locate the nearest cold drinking water line. - Follow the instructions in the ice maker installation kit. 1. Cold Water line 2. Pipe Clamp. 3.Copper (or Plastic) line 4.Compression Nut 5.Compression Sleeve 6.Shut Off Valve 7.Packing Nut. INSTALLATION INSTRUCTIONS Connect the water line to the refrigerator. 1) Slip the compression nut through the provided plastic tubing. 2) Tighten the compression nut onto the 1/4" compression fitting. Refrigerator Ferrule (Not Provided) Compression Nut (1/4 (Provided) NOTE Do not overtighten the compression nut. Using Copper Tubing - Slip the compression nut and ferrule on copper tubing as shown. Using Plastic Tubing - Insert the molded end of the plastic tubing into the compression fitting. 3) Tighten the compression nut onto the compression fitting. 4) Turn water on and check for any leakage. Compression Fitting (Provided) Compression Nut (1/4 (Not Provided) Copper Tubing (Not Provided) Plastic Tubing (Not Provided) Household Water Line Water line must be connected to drinkable water only. NOTE Cut off 1/4 inch of the provided plastic tubing squarely to prevent leaks when reconnecting. Check the water supply line Connect the water pipe with coupler and tap. - Close the main water tap. - Connect coupler "A" to the tap. - Every joint should be protected with sealing tape. WARRANTY INFORMATION This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage. Note: If the coupler does not fit on the current tap, go to the nearest authorised service dealer and purchase the right couplers fittings. 27 CAUTION The water line must be connect- ed to the cold water pipe. If it is connected to the hot water pipe, it may cause the puri- fier to malfunction. COUPLER "A" TAP

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
27
INSTALLATION INSTRUCTIONS
INSTALLATIONOF THE WATER DISPENSER LINE
Connecting to water supply line
- Shut off the main water supply line and turn the Ice
maker to
the off position.
- Locate the nearest cold drinking water line.
- Follow the instructions in the ice maker installation kit.
1. Cold Water line
2. Pipe Clamp.
3.Copper (or Plastic) line
4.Compression Nut
5.Compression Sleeve
6.Shut Off Valve
7.Packing Nut.
Check the water supply line
Connect the water pipe with coupler and tap.
- Close the main water tap.
- Connect coupler “A” to the tap.
- Every joint should be protected with sealing tape.
Note:
If the coupler does not fit on the current tap, go to
the nearest authorised service dealer and purchase
the right couplers fittings.
WARRANTY INFORMATION
This water line installation is not covered by the
refrigerator or ice maker manufacturer's warranty.
Follow these instructions carefully to minimise the risk
of expensive water damage.
TAP
COUPLER “A”
The water line must be connect-
ed to the cold water pipe.
If it is connected to the hot
water pipe, it may cause the puri-
fier to malfunction.
CAUTION
Connect the water line to the refrigerator.
Water line must be connected to drinkable water only.
Cut off 1/4 inch of the provided plastic tubing squarely to prevent leaks when reconnecting.
Do not overtighten the compression nut.
NOTE
NOTE
Compression Nut (1/4
″)
(Provided)
Compression Fitting
(Provided)
Compression Nut (1/4
″
)
(Not Provided)
Plastic Tubing
(Not Provided)
Copper Tubing
(Not Provided)
Ferrule
(Not Provided)
Household Water Line
Refrigerator
1) Slip the compression nut through the provided
plastic tubing.
2) Tighten the compression nut onto the 1/4”
compression fitting.
3) Tighten the compression nut onto the com-
pression fitting.
4) Turn water on and check for any leakage.
●
Using Copper Tubing
- Slip the compression nut and ferrule on
copper tubing as shown.
●
Using Plastic Tubing
- Insert the molded end of the plastic tubing
into the compression fitting.