Samsung UN65C8000XFXZA Quick Guide (easy Manual) (ver.1.0) (English) - Page 1
Samsung UN65C8000XFXZA Manual
View all Samsung UN65C8000XFXZA manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Quick Setup Guide Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly. STOP Please do not return this unit. If you have problems operating your TV, call: 1-800-SAMSUNG (1-800-726-7864) For web support please visit: www.samsung.com/support 1-800-SAMSUNG (1-800-726-7864) Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 Samsung Electronics Canada Inc. 55 Standish Court Mississauga, Ontario L5R 4B2 Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST. To register this product, visit: www.samsung.com/ register. Step 1: Install the Batteries into the Remote To install batteries into your remote control, follow these steps: 1. Lift the cover on the back of the remote upward as shown in the figure to the right. 2. Install two AAA batteries. ✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment. 3. Replace the cover. Step 2: Connect Power and Antenna or Cable Antenna Adapter (Supplied) VHF/UHF Antenna Connect Ant In to Antenna Cable (Not Supplied) or Use a 75 ohm (round) cable. • Wall cable jack • VHF/UHF Antenna • Cable or Satellite box Ant or Cable Out Step 4: Run Plug & Play When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV's channel memorizing process. It also displays connection instructions similar to those in this guide. To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the ENTERE button. To skip a screen, press the MENU button. To turn on your TV, press the POWER button on the remote or on the TV. To run Plug & Play, follow these steps: 1 Using your remote control, select the language for the On Screen Display (OSD), and then press the ENTERE button. Plug & Play Select Language of the OSD. Menu Language : English Español Français 2 Select Home Use, and then press the ENTERE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. U Move E Enter Plug & Play Select the usage mode. Store Demo Home Use Previous U Move E Enter 3 Select Antenna Source and Plug & Play Channel Source. If Antenna Source is Cable or Auto, you must select Channel Source to Antenna Source : Digital Cable System : Air Cable same type as your cable system Analog Cable System : Auto type. After selecting source, select Search; then press the Search ENTERE button on your remote. U Move E Enter Step 3: Connect External Devices Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.) Use one of the connections below to connect your TV to an external A/V device. We recommend using HDMI for the highest picture quality. HDMI Cable (Not Supplied) Best Connection HD connection (up to 1080p) Using an HDMI Cable HDMI OUT DVD, Blu-ray player, HD cable box, HD STB (Set-Top-Box) satellite receiver Device HDMI to DVI Cable (Not Supplied) Audio Cable (Not Supplied) Very Good Connection HD connection (up to 1080p) Using an HDMI to DVI Cable DVI OUT AUDIO OUT Device Component Adapter (Supplied) Lowest Quality Connection AV Adapter (Supplied) Audio/Video connection (480i only) Audio Cable (Not Supplied) Using an Audio/Video Cable AUDIO OUT DVD, Blu-ray player, cable box, STB satellite receiver, VCR VIDEO OUT Device Component Sound in Adapter (Supplied) Audio Cable (Not Supplied) Good Connection Component connection (up to 1080p) Using a Component Cable AUDIO OUT DVD, Blu-ray player, cable box, STB satellite receiver, VCR COMPONENT OUT Device Video Cable (Not Supplied) ✎✎ Most cable systems are Standard (STD) systems, If you are not sure about what kind of cable system you have, contact your cable company. ✎✎ If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box. 4 The TV memorizes the available Plug & Play channels. This process can take Removing scrambled channel. up to 45 minutes. DTV Cable 14 76% DTV Air 0 Air 12 DTV Cable 212 Cable 52 Stop E Enter 5 After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don't, or if you have a cable or satellite box. When done, press the ENTERE button. ✎✎ If you select Manual, the clock setting screen appears. 6 Select the Daylight savings time setting: Off or On, and then press the ENTERE button. Plug & Play Set the Clock Mode. Clock Mode : Auto Manual U Move E Enter Plug & Play Set to daylight saving time. DST : Off On U Move E Enter Component Cable (Not Supplied) 7 Select the time zone in which you live, and then press the ENTERE button. 8 After the time zone screen, The connection method for best HD screen quality is displayed. Press the Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section. 9 The Enjoy your TV. screen appears. Then press the ENTERE button. Changing the Screen Size Your TV has several screen size options, each designed to work best with specific types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. To change the screen size, press the P.SIZE button on your remote. The first time you press it, your TV displays the current setting. Thereafter, each time you press the P.SIZE button, you change the size of the picture on the screen. The following sizes are available: 16:9 Widescreen 4:3 Standard screen Wide Fit Zoom 1 Zoom 2 Screen Fit ✎✎Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) signals are inputted. Connecting an audio device (Home Theater, etc.) Connect your TV to your Home Theater or other audio device to enjoy enhanced Sound quality. Analog Audio connection Using an Audio Cable AUDIO IN Amplifier / DVD Home Theater Optical Adapter (Supplied) Audio Cable (Not Supplied) Optical Cable (Not Supplied) Digital Audio connection Using an Optical Cable Digital Audio System OPTICAL Connecting a PC Connect your TV to a PC to use it as a Monitor. HD connection HDMI to DVI Cable (Not Supplied) Using an HDMI to DVI Cable DVI OUT AUDIO OUT PC Adapter (Supplied) Audio Cable (Not Supplied) Using a D-Sub Cable AUDIO OUT PC OUT D-Sub Cable (Not Supplied) Changing the Picture Mode Your TV has four preset Picture Modes with factory adjusted settings, each designed to give you an excellent picture under specific conditions. The Picture Modes are listed and described in the table below: Mode Dynamic Standard Natural Movie Description Brightens picture. For a vibrant, enhanced image in brightly lit or sunny room. For a bright, detailed picture in a normally lit room. For a comfortable, easy-on-the-eyes picture in a normally lit room. For a studio quality cinema picture in a dimly lit or dark room. To change the Picture Mode, follow these steps: 1. Turn on your TV, press the TOOLS button on your remote. The Tools menu appears. 2. Using the ▲ or ▼ on your remote, select Picture Mode. 3. On the Picture Mode menu, use the ◄ or ► button on your remote to select the Picture Mode you want. 4. Press the EXIT button to exit the menu. Setting the Clock Before you can use your TV's On/Off Timer, you must set the clock. To set the clock, follow these steps: 1. Turn on your TV, press the MENU button on your remote, then select Setup → Time. 2. Select Clock Mode, and then press the ENTERE button. 3. Choose Auto or Manual. xx If you select Auto, the current time will be set automatically using the time from a digital channel. xx If you select Manual, you can set the Month, Day, Year, Hour, Minute and am/pm directly by pressing up, down, left and right arrow button on your remote. 4. Press the RETURN button on your remote when done.