Samsung XL30 User Manual (ENGLISH) - Page 22

Q & A, Windows ME/XP/2000 : Set the resolution at the Control - led monitor

Get Samsung XL30 - SyncMaster - 30inch LCD Monitor PDF manuals and user guides
UPC - 729507801759
View all Samsung XL30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

LED is blinking but no Is the frequency properly Adjust the frequency properly by images on the screen. adjusted when checking the referring to the video card manual Display Timing on the menu? and Preset Timing Modes. There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Have the Windows colors been set properly? Has the video card been set properly? (The maximum frequency per resolution may differ from product to product.) Windows ME/2000/XP : Set the colors properly at the Control Panel → Display → Settings. Set the video card by referring to the video card manual. I cannot use the 2560x1600 resolution with the monitor. Does the graphics card on your computer support the 2560x1600 resolution? If your graphics card does not support the 2560x1600 resolution, then you can only use the 1280x800 resolution with your monitor. To use the 2560x1600 resolution, replace your graphics card with one that supports that resolution. Check the following items if there is trouble with the monitor. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, ask the service center to check the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver. 4. Check if the scanning ratio of the video screen is set at 60 Hz +/- 2 Hz. (Do not exceed 60 Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel→System→Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized Service Center. Q & A Question Answer How can I change the frequency? The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control Panel→Display→Settings. * Contact the video card manufacturer for details. How can I set the Power Saving Windows ME/XP/2000 : Set the function at BIOS-SETUP of the function? computer or the screen saver. (Refer to Windows/Computer Manual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the monitor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
LED is blinking but no
images on the screen.
Is the frequency properly
adjusted when checking the
Display Timing on the menu?
Adjust the frequency properly by
referring to the video card manual
and
Preset Timing Modes
.
(The maximum frequency per
resolution may differ from product to
product.)
There are only 16
colors shown on the
screen.
The screen colors
have changed after
changing the video
card.
Have the Windows colors
been set properly?
Windows ME/2000/XP :
Set the colors properly at the
Control Panel
→
Display
→
Settings
.
Has the video card been set
properly?
Set the video card by referring to the
video card manual.
I cannot use the
2560x1600 resolution
with the monitor.
Does the graphics card on
your computer support the
2560x1600 resolution?
If your graphics card does not support the
2560x1600 resolution, then you can only
use the 1280x800 resolution with your
monitor.
To use the 2560x1600 resolution, replace
your graphics card with one that supports
that resolution.
Check the following items if there is trouble with the monitor.
1.
Check if the power cord and the video cables are properly connected to the computer.
2.
Check if the computer beeps more than 3 times when booting.
(If it does, ask the service center to check the main board of the computer.)
3.
If you installed a new video card or if you assembled the PC, check if the installed the adapter
(video) driver.
4.
Check if the scanning ratio of the video screen is set at 60 Hz +/- 2 Hz.
(Do not exceed 60 Hz when using the maximum resolution.)
5.
If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "
Control Panel
→
System
→
Device Administrator
" and then
reboot the computer to reinstall the adapter (video) driver.
If problems repeatedly occur,
contact an authorized Service Center
.
Q & A
Question
Answer
How can I change the
frequency?
The frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version
of the driver used. (Refer to the computer or the video card
manual for details.)
How can I adjust the resolution?
Windows ME/XP/2000 : Set the resolution at the Control
Panel
→
Display
→
Settings.
* Contact the video card manufacturer for details.
How can I set the Power Saving
function?
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the
computer or the screen saver. (Refer to Windows/Computer
Manual).
How can I clean the outer
case/LCD Panel?
Disconnect the power cord and then clean the monitor with a soft
cloth, using either a cleaning solution or plain water.
Do not leave any detergent or scratches on the case. Do not let
any water enter the monitor.