Sanyo EF30NL Owners Manual
Sanyo EF30NL - SXGA LCD Projector Manual
 |
View all Sanyo EF30NL manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo EF30NL manual content summary:
- Sanyo EF30NL | Owners Manual - Page 1
Multimedia Projector MODEL PLC-EF30 SANYO =7, 00 0 0 0 000 * Projection lens is optional. Owner's Manual - Sanyo EF30NL | Owners Manual - Page 2
to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. /44+4\ SAFETY - Sanyo EF30NL | Owners Manual - Page 3
service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions - Sanyo EF30NL | Owners Manual - Page 4
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of the equipment. AC POWER CORD REQUIREMENT The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power - Sanyo EF30NL | Owners Manual - Page 5
NAME OF EACH PART OF PROJECTOR 7 AUTO PC ADJUSTMENT 28 SETTING-UP PROJECTOR CONNECTING AC POWER CORD 8 MANUAL PC ADJUSTMENT 29 8 PICTURE ON / OFF PROJECTOR 21 LAMP MANAGEMENT 44 ADJUSTING SCREEN 22 LAMP REPLACEMENT 45 ZOOM ADJUSTMENT 22 TROUBLESHOOTING 46 FOCUS ADJUSTMENT LENS - Sanyo EF30NL | Owners Manual - Page 6
consumption while a projector is not in use. This Power Management function operates to turn Projection Lamp off when a projector detects signal interruption of a projector may result in distorted image being displayed in a trapezoid shape. Keystone Correction solves this problem by digitally - Sanyo EF30NL | Owners Manual - Page 7
metallic parts. This area will become hot while a projector is used. This projector detects internal temperature and automatically controls operating power of Cooling Fans. LAMP COVER MAIN ON / OFF SWITCH BOTTOM O. AIR INTAKE VENTS This projector is equipped with cooling fans for protection from - Sanyo EF30NL | Owners Manual - Page 8
do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of type of power supply being in use. Connect a projector with a peripheral equipment before turning a projector on. (Refer to pages 12 - 15 for connection.) Connect AC Power Cord - Sanyo EF30NL | Owners Manual - Page 9
lens. For specifications of a Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a projector. 2. For installation, refer to installation manual supplied to a Projector. When moving or setting up a projector, be sure to replace Lens Cover to protect - Sanyo EF30NL | Owners Manual - Page 10
, use a suitable carrying case. • Do not transport a projector by using a courier or transport service in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer and best case should be applied. 10 - Sanyo EF30NL | Owners Manual - Page 11
Boards. For Terminal Boards, contact sales dealer where you purchased a projector. NOTE; DVI Terminal is unavailable for INPUT 3 slot. a INPUT Insert terminal along Guide to fit Plug into Socket. 4 Tighten screws to secure terminal. 0 © 1 Co C-J 0 Screws Guide Socket Plug Figure shows - Sanyo EF30NL | Owners Manual - Page 12
000. o0o0o 0, RESET AUDIO OUT O - • • • (MO USB = INPUT 3/ INPUT 1, 2 CONTROL PORT CONNECTORS When controlling computer with Remote Control of this projector, connect mouse port of your personal computer to these connectors. (Refer to P14.) INPUT 3 AV INPUT (VIDEO/Y, C) JACKS Connect - Sanyo EF30NL | Owners Manual - Page 13
Wired Remote Control, Connect Wired Remote Control Unit to this jack with Remote Control Cable (supplied). (Refer to page 18.) RESET BUTTON This projector uses a micro processor to control a unit. Occasionally, this micro processor may malfunction and need to be reset. This can be done by pressing - Sanyo EF30NL | Owners Manual - Page 14
= AUDIO OUT Audio Cable (stereo) * Set switches as shown in table below depending on RESOLUTION MODE that you want to use before your turn on a projector and computer MODE SWITCHES 1 2 3 4 5 6 13"MODE (640 x 480) OFF OFF OFF OFF 16"MODE (832 x 624) OFF OFF OFF OFF 19"MODE (1024 x768) OFF - Sanyo EF30NL | Owners Manual - Page 15
o ® ® SERIAL PORT IN RCJACK 3 S o(::::)O SERIAL PORT OUT o(=lo o AUDIO OUT M 0 * 0 1 .,eicliaJ CD 0[i USB = INPUT 3 I INPUT 2 INPUT 1 j AV AUDIO IN Terminals of a Projector AUDIO OUT Audio Cable (Stereo) * Audio Input External Audio Equipment Audio Amplifier Audio Speaker (stereo) 15 - Sanyo EF30NL | Owners Manual - Page 16
draws to an end. (P44, 45) WARNING TEMP. INDICATOR Flashes red when internal projector temperature is too high. (P42) •I I • AUTO PC ADA CT Lights green when a LAMP R REPLACE TE projector is ready to be turned on. And it flashes green in Power Management mode. (P40) MENU BUTTON Used - Sanyo EF30NL | Owners Manual - Page 17
PUT i2 ( ) ( MENU INPUT 3 ER AS- LENS SHIF KEYSTONE NO SHOW FREEZE ( AUTO PC ADJ. ._ IMAGE P-TIMER POWER ON-OFF BUTTON Used to turn projector on or off. (P21) INPUT 1/2 BUTTON Used to select input source either INPUT 1 or INPUT 2. (P25) INPUT 3 BUTTON Used to select input source (INPUT - Sanyo EF30NL | Owners Manual - Page 18
DIGITAL ZOOM +1- mode and resize image. (P33) Operating Range Point Remote Control Unit toward projector (Receiver Window) whenever pressing any button. Maximum operating range for Remote Control Unit is about of used batteries according to the batteries manufacturers instructions and local rules. - Sanyo EF30NL | Owners Manual - Page 19
BEFORE OPERATION OPERATING ON-SCREEN MENU HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through ON-SCREEN MENU. Refer to following pages to operate each adjustment on ON-SCREEN MENU. 1 DISPLAY MENU Press MENU button to display ON-SCREEN - Sanyo EF30NL | Owners Manual - Page 20
Press MENU BUTTON while connecting to PC input source. GUIDE WINDOW Shows selected item of ONSCREEN MENU. PC SYSTEM Wide / Digital zoom +/-] (Refer to P33) SETTING MENU Used to change settings of projector or reset Lamp Replace Counter. (Refer to P39-41) Input SVGA 2 INPUT MENU Used to select - Sanyo EF30NL | Owners Manual - Page 21
-OFF button again to turn off projector. LAMP indicator lights bright and READY indicator turns off. After MAINTAIN LIFE OF LAMP, ONCE YOU TURN • PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE section on page 43.) 4. Turn a projector on again. If WARNING TEMP. indicator should still continue - Sanyo EF30NL | Owners Manual - Page 22
BASIC OPERATION ADJUSTING SCREEN ZOOM ADJUSTMENT 1 Press ZOOM A/V button on Top Control or on Remote Control Unit. Message "Zoom" is displayed. 2 Press ZOOM A button to make image larger, and press ZOOM V button to make image smaller. Zoom Message disappears after 4 seconds. FOCUS ADJUSTMENT 1 - Sanyo EF30NL | Owners Manual - Page 23
BASIC OPERATION PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button except POINT / SELECT / RIGHT CLICK / P-TIMER / LASER button. NO SHOW FUNCTION Press NO SHOW button on - Sanyo EF30NL | Owners Manual - Page 24
BASIC OPERATION SOUND ADJUSTMENT DIRECT OPERATION Volume Press VOLUME (+/-) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on screen for a few seconds. (+) button to increase volume, and (-) button for decreasing. Mute Press MUTE button on Remote - Sanyo EF30NL | Owners Manual - Page 25
COMPUTER INPUT SELECTING INPUT SOURCE DIRECT OPERATION Select INPUT source by pressing INPUT 1/2 and INPUT 3 buttons on Remote Control Unit. Select INPUT source by pressing INPUT A/V button on Top Control. MENU OPERATION 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT - Sanyo EF30NL | Owners Manual - Page 26
Menu icon. (Refer to P28.) When image is not provided properly, manual adjustment is required. (Refer to P29 and 30.) There is no signal input from computer. Make sure connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 46.) PC SYSTEM MENU PC SYSTEM Menu icon - Sanyo EF30NL | Owners Manual - Page 27
COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 230 MHz of Dot Clock. ON-SCREEN DISPLAY VGA 1 VGA 2 VGA 3 VGA 4 - Sanyo EF30NL | Owners Manual - Page 28
Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, setting can be done just by selecting Mode Adjustment function. When image is not provided properly through this function, manual adjustments are required. (Refer to page 29, 30.) • Auto - Sanyo EF30NL | Owners Manual - Page 29
cannot reproduce a proper image and image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This - Sanyo EF30NL | Owners Manual - Page 30
POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. w Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to - Sanyo EF30NL | Owners Manual - Page 31
to move a red frame pointer to level that you want to set and then press SELECT button. Standard I Normal picture level preset on this projector. II Real n Picture level with improved halftone for graphics. IMAGE SELECT Menu icon Move a red frame icon to level and press SELECT button. ❑1 IMAGE - Sanyo EF30NL | Owners Manual - Page 32
is changed to "Off" and progressive scan mode to off. Press POINT LEFT/RIGHT button(s) again, progressive scan mode to on. 3 Store To store manually preset image, move a red frame pointer to Store icon and press SELECT button. Image Level Menu will appear. Move a red frame pointer to Image - Sanyo EF30NL | Owners Manual - Page 33
• Wide cannot be selected when "720p (HDTV)", "1035i (HDTV)", "1080i50 (HDTV)" or "1080i60 (HDTV)" is selected on PC SYSTEM Menu (P26). • This projector cannot display any resolution higher than 1600 X 1200. If your computer's screen resolution is higher than 1600 X 1200, reset resolution to lower - Sanyo EF30NL | Owners Manual - Page 34
VIDEO INPUT SELECTING INPUT SOURCE WHEN SELECT INPUT 2 (5 BNC INPUT JACKS ) When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from INPUT MENU video equipment to R/Pr, G/Y and B/Pb jacks. 1/ Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red - Sanyo EF30NL | Owners Manual - Page 35
signal, and adjusts itself to optimize its performance. When Video System is 1035i, 1080i50 or 1080i60, select system manually first. COMPONENT VIDEO SIGNAL FORMAT If projector cannot reproduce proper video image, it is necessary to select a specific component video signal format among 480i, 575i - Sanyo EF30NL | Owners Manual - Page 36
move a red frame pointer to level that you want to set and then press SELECT button. 4.+ Standard Normal picture level preset on this projector. IMAGE SELECT Menu icon Cinema Picture level adjusted for picture with fine tone. Di IMAGE 1-4 User preset picture adjustment in IMAGE ADJUST Menu (P38 - Sanyo EF30NL | Owners Manual - Page 37
VIDEO INPUT IMAGE LEVEL ADJUSTMENT 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to IMAGE ADJUST Menu icon. IMAGE ADJUST MENU 2 Press POINT DOWN button to move a red frame pointer to item that you want to adjust and then press - Sanyo EF30NL | Owners Manual - Page 38
Store icon Image Level Menu Move a red frame pointer to image icon to be set and then press SELECT button. PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display desirable image size. 1 Press MENU button and ON-SCREEN MENU will appear. Press - Sanyo EF30NL | Owners Manual - Page 39
all On-Screen Displays. Off sets On-Screen Displays disappeared except; • ON-SCREEN MENU • "Power off?" message Logo When this function is "On," projector displays our logo when starting up. Ceiling When this function is "On," picture is top/bottom and left/right reversed. This function is used to - Sanyo EF30NL | Owners Manual - Page 40
item and then press POINT LEFT/RIGHT button(s). jr), Lamp Mode This Projector is equipped with 2 Projection Lamps and a number of using lamps can be switched to 2 lamps or 1 lamp. Using 1 lamp maintain life of Projection Lamps. To change over Lamp Mode 1. Press MENU button and ON-SCREEN MENU will - Sanyo EF30NL | Owners Manual - Page 41
a projector by computer, install USB driver (optionally sold parts) and set up computer following instruction in USB driver package. Contact your authorized dealer. Press SELECT button at this icon to display previous items. ` Move a pointer to item and then press POINT LEFT/RIGHT button(s). Lamp - Sanyo EF30NL | Owners Manual - Page 42
has no mouse port, connect Serial Port of your computer to Control Port of a projector with Control Cable for Serial Port (not supplied). OPERATING WIRELESS MOUSE When controlling a PC Cooling Fans or Internal Circuits may be malfunctioning. Contact service personnel from an authorized dealer or - Sanyo EF30NL | Owners Manual - Page 43
from an AC outlet. 2 Pull out 3 Air Filters and Air filter Covers from a projector. 3 Clean each parts (Air Filter and Air filter Cover) with brush or wash out above symptoms are noticed, contact your authorized dealer or service station for proper cleaning. CLEANING PROJECTION LENS Follow these - Sanyo EF30NL | Owners Manual - Page 44
Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp. When any of 2 lamps becomes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2 lamps or 1 lamp manually. Refer to SETTING section on page 39, 40. 44 - Sanyo EF30NL | Owners Manual - Page 45
we recommend replacing all 2 lamps at a time. ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give following information to dealer. • Model No. of your projector : PLC-EF30 • Replacement Lamp Type No. : POA-LMP39 (Service Parts No. 610 292 - Sanyo EF30NL | Owners Manual - Page 46
APPENDIX TROUBLESHOOTING Before calling your dealer or service center for assistance, check matters below once again. 1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 - 15. 2. Check cable connection. Verify - Sanyo EF30NL | Owners Manual - Page 47
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOTING" section on page 46, 47. To correct failure, try "Solutions". If after following all operating instructions, you find that service is necessary, contact Sanyo Service Station or store where - Sanyo EF30NL | Owners Manual - Page 48
Lamp Input 1 Jacks Input 2 Jacks Input 3 Jacks Other Jacks Built-in Speakers Feet Adjustment Voltage and Power Consumption Operating Temperature Storage Temperature Remote Control Transmitter Accessories Multi-media Projector length : 650±20nm) Owner's Manual AC Power Cord Wireless/Wired Remote - Sanyo EF30NL | Owners Manual - Page 49
APPENDIX CONFIGURATIONS OF TERMINALS DVI-I TERMINAL (DIGITAL/ANALOG) This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this terminal with DVI cable (supplied). Pin Configuration Cl C2 (7 111111EEM111111 =MEM nnononon C3 C4 C5 - Sanyo EF30NL | Owners Manual - Page 50
APPENDIX USB PORT TERMINAL Pin Configuration Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port Cable (not supplied). 1 Vcc 2 - Data 3 + Data 4 Ground 50 - Sanyo EF30NL | Owners Manual - Page 51
APPENDIX 51 - Sanyo EF30NL | Owners Manual - Page 52
Printed in Japan Part No. 610 293 4960 (1AA6P1P2836-- MV6A) SANYO SANYO Electric Co., Ltd
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
 |
 |
