Sanyo PLC-XF71 Owners Manual
Sanyo PLC-XF71 - XGA LCD Projector Manual
 |
UPC - 086483072451
View all Sanyo PLC-XF71 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-XF71 manual content summary:
- Sanyo PLC-XF71 | Owners Manual - Page 1
Multimedia Projector MODEL PLC-XF71 ✽ Projection lens is optional. Owner's Manual - Sanyo PLC-XF71 | Owners Manual - Page 2
function reduces power consumption and maintains lamp life (p.52). ◆ Automatic Filter Replacement Function The projector monitors the condition of the filter and replaces a filter automatically when it detects the clogging. ◆ Shutter Function The projector is equipped with the shutter that - Sanyo PLC-XF71 | Owners Manual - Page 3
and Care 57 Filter Instructions 57 Replacing the Filter Cartridge 58 Resetting the Filter Counter 59 Resetting the Scroll Counter 59 Lamp Management 60 Lamp Replacement 61 Resetting the Lamp Counter 62 Cleaning the Projection Lens 64 Cleaning the Projector Cabinet 64 Warning - Sanyo PLC-XF71 | Owners Manual - Page 4
of this manual. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT - Sanyo PLC-XF71 | Owners Manual - Page 5
with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement - Sanyo PLC-XF71 | Owners Manual - Page 6
clogged and no scroll is left in the filter cartridge, a Filter cartridge replacement icon (Fig. 2) appears on the screen and WARNING FILTER indicator on the top panel lights up (see below). Stop using the projector immediately and replace the filter cartridge. Blocking the air vents and leaving the - Sanyo PLC-XF71 | Owners Manual - Page 7
designed for this projector. When not mounted properly, the projector may fall, causing hazards or injury. For details, consult your dealer. The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an - Sanyo PLC-XF71 | Owners Manual - Page 8
case. This may cause damage to the projector. For information about transporting the projector by courier or any other transport service, consult your dealer. -Do not put the projector in a case before it is cooled enough. -Do not transport the projector with a replacement lens installed. 8 - Sanyo PLC-XF71 | Owners Manual - Page 9
if not installed and used in accordance with the instruction manual, may cause user may be required to take adequate measures. AC Power Cord Requirement The AC Power Cord supplied with this projector face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of - Sanyo PLC-XF71 | Owners Manual - Page 10
Lens Mount Cover w Projection Lens (Option) e Indicators r Infrared Remote Receiver (Front) t Adjustable Feet y Terminals and Connectors u Handle i Side Control o Lamp Air Filter Cover ✽Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector. *Kensington - Sanyo PLC-XF71 | Owners Manual - Page 11
can be controlled with one computer by connecting SERIAL PORT IN of another projector to this terminal. e USB CONNECTOR (Series B) USB connector is to used to service the projector. r R/C JACK When using the wired remote control, connect the wired remote control to this jack with a remote control - Sanyo PLC-XF71 | Owners Manual - Page 12
q u w i e o !0 r t !1 y q ON/STAND-BY button Turn the projector on or off. (pp.23,24) w ZOOM button Zoom in and out the images. (p. the computer image to its optimum setting. (pp.27, 35) 12 u LENS SHIFT button Select the LENS SHIFT function. (p.27) i FOCUS button Adjust the focus. (p.27) o - Sanyo PLC-XF71 | Owners Manual - Page 13
installed (pp.57, 74). -Light orange when the clogging of the filter is detected or the filter counter reaches a time set in the timer setting, urging immediate filter/ filter cartridge replacement (pp.56, 57, 74). t SHUTTER indicator Light blue when the shutter is closed. (p72) y LAMP 2 REPLACE - Sanyo PLC-XF71 | Owners Manual - Page 14
other chemical materials. q ON/STAND-BY button Turn the projector on or off. (pp.23-24) w AUTO PC in DIGITAL ZOOM +/- mode. (p.40) y LENS SHIFT button Select the LENS SHIFT function. (p.29) u FOCUS buttons Adjust (pp.30, 40, 44) !3 FILTER button Scroll the filter. (p.30) !4 SHUTTER button Close the - Sanyo PLC-XF71 | Owners Manual - Page 15
wipe the case clean and install new batteries. ● Risk of an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Receivers and Operating Range Point the remote control toward the projector (to Infrared Remote Receivers - Sanyo PLC-XF71 | Owners Manual - Page 16
release the IMAGE ADJ. button the number of corresponding times you would like to set the number of the remote control code for the projector. Reset position Use position Reset switch Remote Control Code Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Number of Times Pressing IMAGE ADJ - Sanyo PLC-XF71 | Owners Manual - Page 17
For the specifications of Projection Lens, contact sales dealer where you purchased the projector. - Do not use the optional lens below for this projector. Otherwise damages may result. LENS MODEL NO. : LNS-T01, LNS-T01Z - Lens installation and replacement should be made by the qualified service - Sanyo PLC-XF71 | Owners Manual - Page 18
to leftmost. When the lens is shifted to rightmost. Picture Level and Pitch Adjustment The projection angle is adjustable up to 2.8 degrees upward and downward respectively by rotating front and back feet . To raise the projector, rotate the feet clockwise. To lower the projector or to retract the - Sanyo PLC-XF71 | Owners Manual - Page 19
Terminals of Projector The projector has two replaceable Interface board slots. The projector's functions can be extended by installing the optional interface boards into the terminal slots. 2 vacant slots (Input 3 and 4) are provided in your purchasing the projector. For the Optional Interface - Sanyo PLC-XF71 | Owners Manual - Page 20
Installation Connecting to Computer Cables used for connection • VGA Cable (D-sub 15 pin) * • DVI Cable • BNC Cable (BNC x 5) ( *One cable is supplied; Other cables are not supplied with this projector.) Laptop type Desktop type Monitor Output Monitor Output Monitor Output DVI Cable DIGITAL - Sanyo PLC-XF71 | Owners Manual - Page 21
(BNC x 3, BNC x 1) • SCART-VGA Cable • DVI Cable • S-Video Cable ( Cables are not supplied with the projector.) Video Source (example) Video Cassette Recorder Video Disc Player Installation Component video output equipment. (such as DVD player or high-definition TV source.) Digital Output RGB - Sanyo PLC-XF71 | Owners Manual - Page 22
Installation Connecting the AC Power Cord This projector service station. Connect the projector with all peripheral equipment before turning on the projector Projector side For the U.S.A. and Canada Ground AC Outlet side For Continental Europe For the U.K. To POWER CORD CONNECTOR on your projector - Sanyo PLC-XF71 | Owners Manual - Page 23
will disappear after 20 seconds. Selected Input Source and Lamp control Lamp mode See page 60 for the Lamp mode status ✔Note: •The Lamp replacement icon and the Filter warning icon may appear on the screen depending on the usage state of the projector. PIN code Input Dialog Box After the OK icon - Sanyo PLC-XF71 | Owners Manual - Page 24
completely cooled down. 4 Unplug the AC power cord from the AC outlet. TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST FIVE MINUTES BEFORE TURNING IT OFF. DO NOT UNPLUG THE AC POWER CORD WHILE COOLING FANS ARE RUNNING OR BEFORE THE - Sanyo PLC-XF71 | Owners Manual - Page 25
How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the side control or the remote control to display the On-Screen Menu. 2 Use the - Sanyo PLC-XF71 | Owners Manual - Page 26
on pages 69-71. For Computer Source q w e r tyu i o q Guide Window Show the selected Menu of the On-Screen Menu. w Input Menu Used to select / Full screen/Custom/Keystone/Ceiling/Rear/Reset/Digital zoom +/-] (pp.39-40). i Setting Menu Used to set the projector's operating configurations (pp. 48 - Sanyo PLC-XF71 | Owners Manual - Page 27
arrow turns red when the lens shift comes to the center position of the screen. ✔Note: • The SHUTTER button on the side control and the remote control cannot be effective when Shutter Protection is "On" in the Setting menu. (p.55) • The SHUTTER indicator on the projector's top lights blue when the - Sanyo PLC-XF71 | Owners Manual - Page 28
Basic Operation Information Information display can be used to confirm the current operating condition of the projector and the signal being projected through the projector. Press the INFORMATION button to display the information window on the screen. To hide the information window, press the - Sanyo PLC-XF71 | Owners Manual - Page 29
be done easily by pressing this button. See page 35 for details. LENS SHIFT button See page 27 for details. ZOOM buttons Press the ZOOM buttons . See the previous page for details. Remote Control AUTO PC button LENS SHIFT button ZOOM buttons POINT ed7 8 buttons SCREEN button FOCUS buttons - Sanyo PLC-XF71 | Owners Manual - Page 30
See page 27 for details. FILTER button Press and hold the FILTER button for more than five seconds to replace the filter mechanically. See page 51 for details. ✔Note: •The filter cannot be rewound. • When the filter is replaced, the total accumulated time of the filter use is automatically set to - Sanyo PLC-XF71 | Owners Manual - Page 31
Input Selection Input Side Control Side Control button operation INPUT button Side Control Operation Press the INPUT button on the side control. It switches to INPUT 1, INPUT 2, INPUT 3 and INPUT 4 as you press the INPUT button. Before using the INPUT button on the side control, you must select - Sanyo PLC-XF71 | Owners Manual - Page 32
Input Selection Computer Input Source Selection Menu Operation When Selecting the INPUT 1 with DVI/D-sub 15 terminals 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the INPUT Menu icon. INPUT MENU 2 Use the Point ed buttons to - Sanyo PLC-XF71 | Owners Manual - Page 33
content which is delivered by DVI (Digital Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. •When a slot is empty - Sanyo PLC-XF71 | Owners Manual - Page 34
projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+, WXGA, UXGA, or WUXGA (refer to "Compatible Computer Specifications your computer and the projector. (See "Troubleshooting" on page 66.) Mode 1 The preset system is manually adjusted in the PC Adjust - Sanyo PLC-XF71 | Owners Manual - Page 35
parameters. The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.34). See MANUAL PC ADJUSTMENT on pages 36-37. ✔Note: •Fine sync, Total dots, Horizontal and Vertical - Sanyo PLC-XF71 | Owners Manual - Page 36
you to precisely adjust several parameters to match those special signal formats. The projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. ✔Note: The PC Adjust Menu cannot be operated when the digital - Sanyo PLC-XF71 | Owners Manual - Page 37
Computer Input Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box appears and then select [Yes]. All adjustments will return to their previous figures. Mode free To clear the adjusted data, select Mode free and then press the SELECT button. Move the red - Sanyo PLC-XF71 | Owners Manual - Page 38
to the desired image level and then press the SELECT button. Standard Normal picture level preset on the projector. Real Picture level with improved halftone for graphics. IMAGE 1-10 User preset picture adjustment in the Image Adjust Menu. (p. 47) IMAGE SELECT MENU Image Select Menu icon Move the - Sanyo PLC-XF71 | Owners Manual - Page 39
before connecting the projector. •The image data other than XGA (1024 x 768) is modified to fit the screen size in initial mode. •The panning function may not operate properly if the stored Mode in the PC Adjust Menu is used. (p. 37) Custom Adjust the screen scale and position manually - Sanyo PLC-XF71 | Owners Manual - Page 40
When this function is set to "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to "On," the picture is left/right reversed. This function is used to project the image from the rear - Sanyo PLC-XF71 | Owners Manual - Page 41
itself to optimize its performance. When the Video System is 1035i or 1080i, select the system manually. COMPONENT VIDEO SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i. AV - Sanyo PLC-XF71 | Owners Manual - Page 42
pointer to the desired image level and then press the SELECT button. Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. IMAGE 1-10 User preset picture adjustment in the Image Adjust Menu. (p. 47) IMAGE SELECT MENU Image Select Menu icon Move the red - Sanyo PLC-XF71 | Owners Manual - Page 43
at the normal video aspect ratio of 4:3. Wide Provide the image at the wide screen ratio of 16:9. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and the "Custom" is displayed on the screen for a few seconds. To display the Aspect dialog - Sanyo PLC-XF71 | Owners Manual - Page 44
When this function is set to "On," the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to "On," the picture is left/right reversed. This function is used to project the image from the rear - Sanyo PLC-XF71 | Owners Manual - Page 45
can be used to adjust the LEVEL, PHASE, and GAMMA of the selected display colors (except for black, white, and gray) on the screen and replace these colors with other colors if required. You can store up to eight (8) color management data. 1 Use the Point ed buttons to move the red - Sanyo PLC-XF71 | Owners Manual - Page 46
Picture Image COLOR SELECTION MODE (continued) COLOR M. Return to the COLOR MANAGEMENT POINTER. (If you press the MENU button on the side control or the remote control, it returns to the COLOR MANAGEMENT POINTER and you will need to reselect and readjust the color.) MENU Return to the IMAGE ADJUST - Sanyo PLC-XF71 | Owners Manual - Page 47
progressive scan mode. Off Progressive scan mode is "Off." On Progressive scan mode is "On." Film For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. ✔Note: •Picture is distorted at the moment of On/Off /Film switching. Reset To reset - Sanyo PLC-XF71 | Owners Manual - Page 48
when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. displayed when no input signal is detected. Blue Blue colored background. User The image you captured. Black Black colored background. 48 Menu Set - Sanyo PLC-XF71 | Owners Manual - Page 49
the projected image. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image will be displayed the next time you turn on the projector. To cancel the Capture function, select [No]. ✔Note: •Before capturing an image, select "Standard" in the - Sanyo PLC-XF71 | Owners Manual - Page 50
Setting Logo PIN code lock This function prevents an unauthorized person from changing the screen logo. Off The screen logo can be changed freely from the Logo Menu. On The screen logo cannot be changed without a Logo PIN code. If you want to change the Logo PIN code lock setting, press the - Sanyo PLC-XF71 | Owners Manual - Page 51
becomes brighter gradually. ✔Note: • When neither of the two lamps is lighted, the projector will shutdown automatically. • When either of the two lamps does not light up, the LAMP 1/2 REPLACE indicator blinks orange and the projector will light the other automatically. • After changing the - Sanyo PLC-XF71 | Owners Manual - Page 52
. Back Activate only the back receiver. Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. If the input signal is interrupted and no button is pressed - Sanyo PLC-XF71 | Owners Manual - Page 53
becomes locked and you do not have the remote control nearby and unable to operate the projector, contact the service station. PIN code lock This function prevents the projector from being operated by unauthorized persons and provides the following setting options for security. Off Unlocked - Sanyo PLC-XF71 | Owners Manual - Page 54
pin code no. memo on page 80, and keep it securely. If you forget your pin code, the projector can no longer be started. Projector ID This feature allows users to set serial communication configuration (Projector ID) when several projectors are connected via the RS-232C terminal (serial port) of the - Sanyo PLC-XF71 | Owners Manual - Page 55
turns off the projection lamp when the projector is left with the Lamp replacement icon appears on the screen, indicating that the end of lamp life is approaching. When replacing the projection lamp, reset the lamp counter. See "Resetting the Lamp Counter" on page 62. ✔Note: •The Lamp replacement - Sanyo PLC-XF71 | Owners Manual - Page 56
cartridge. •Timer setting notifies that the filter needs replacement. To replace the filter, use the filter control function (p.51). Test pattern Various test pattern are available for use when setting up the projector. Factory default This function returns all setting values except for the user - Sanyo PLC-XF71 | Owners Manual - Page 57
work properly. It may cause a breakdown. •Make sure that the projection lamps are turned off when you are replacing the filter cartridge. If you replace the filter cartridge when the projection lamps are turned on, the projector will be shut down automatically for safety purposes. •Do not forget - Sanyo PLC-XF71 | Owners Manual - Page 58
dealer or service station for proper cleaning. ORDER REPLACEMENT FILTER CARTRIDGE Replacement filter cartridge can be ordered through your dealer. When ordering, give the following information to the dealer. ● Model No. of your projector PLC-XF71 ● Replacement Filter Cartridge Type No - Sanyo PLC-XF71 | Owners Manual - Page 59
. Select [Yes] to continue. 4 Another confirmation dialog box appears, select [Yes] to reset the Filter counter. Resetting the Scroll Counter Be sure to reset the Scroll counter after replacing the filter cartridge. 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to - Sanyo PLC-XF71 | Owners Manual - Page 60
and flash when any of them becomes out. Check the number of lamp on the Lamp Status Display or the LAMP 1/2 REPLACE indicators and replace the lamp. Lamp Status Display The Lamp Status Display appears on screen when the projector is turned on or the input position (input 1, input 2, Input 3 or input - Sanyo PLC-XF71 | Owners Manual - Page 61
steps to replace the lamp. For continued safety, replace with a lamp assembly of the same type. Do not drop the lamp assembly or touch a glass bulb! The glass can shatter and may cause injury. 1 Check the number of lamp to be replaced on the Lamp Status Display. 2 Turn off the projector, press - Sanyo PLC-XF71 | Owners Manual - Page 62
to reset the lamp counter. ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer. ● Model No. of your projector : PLC-XF71 ● Replacement Lamp Type No. : POA-LMP128 (Service Parts No - Sanyo PLC-XF71 | Owners Manual - Page 63
the lamp should be replaced, i.e., if the LAMP 1/2 REPLACE indicators light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP 1/2 REPLACE - Sanyo PLC-XF71 | Owners Manual - Page 64
Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the lens. Cleaning the Projector Cabinet Turn off the projector, press the Main On/Off Switch to Off and unplug the AC power cord from the AC outlet before cleaning. Gently - Sanyo PLC-XF71 | Owners Manual - Page 65
are not blocked. - Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent. - Is the filter clean? Replace the filter with a new one. The projector is shut down; and the LAMP indicator is lighting and other - Sanyo PLC-XF71 | Owners Manual - Page 66
Lamp mode icon appears. - That is the Lamp replacement icon or the Filter warning icon. See page 55-56. No image. - Check the connection between your computer or video equipment and the projector connected to the projector. See your computer's instruction manual for the setting. - It takes - Sanyo PLC-XF71 | Owners Manual - Page 67
lamp life is approaching. Replace the lamp with a new one promptly. (See page 55) -The filter is out of scroll. Replace the filter cartridge with a new one promptly. (See pages 57-58) appears on the screen The image is out of focus. - Adjust the focus of the projector. - Check Projection Lens - Sanyo PLC-XF71 | Owners Manual - Page 68
center. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the - Sanyo PLC-XF71 | Owners Manual - Page 69
(2) Go to System (2) Information Information Image Adjust Input H-sync freq. V-sync freq. Screen Language Lamp mode Lamp control Power management Shutter management Remote Control Projector Security 5 - 180 Min Key lock Remote control PIN code lock Image Adjust Contrast Brightness Color - Sanyo PLC-XF71 | Owners Manual - Page 70
on the input signal. 70 Image Select Standard Real Image 1 Image 10 Screen Normal True Wide Full screen Custom Digital zoom + Digital zoom Keystone Ceiling Rear Reset Quit Scale H &V Position Common Reset H /V On/Off H /V Quit Store Reset On/Off On/Off Yes/No Screen System (3) Auto 1080i - Sanyo PLC-XF71 | Owners Manual - Page 71
Remote Control Off/On1/On2 PIN code change Quit Remote control Projector On / Off On / Off Management 5 - 180 Min. Quit Lamp counter Lamp 1/2 [ ] Hour(s) Reset Yes/No Quit Filter counter Test pattern Factory default Quit Used time [ ] Hour(s) Off/400H/700H/1000H Reset Quit Yes - Sanyo PLC-XF71 | Owners Manual - Page 72
completed and the READY indicator lights green. The projection lamp is being cooled down in the ✽ ✽ Power management mode. ✽ ✽ The projector is in the Power management mode. ✽ ✽ ✽ Fig.1 Filter replacement icon and "Please wait..." The projection lamp is being cooled down in the ✽ Shutter - Sanyo PLC-XF71 | Owners Manual - Page 73
orange, replace the filter or the filter cartridge with a new one promptly. Reset the Filter counter and Scroll counter after replacing the filter cartridge (p.59). LAMP REPLACE 1 and 2 When the LAMP 1 REPLACE indicator and the LAMP 2 REPLACE indicator light orange, replace the projection lamps with - Sanyo PLC-XF71 | Owners Manual - Page 74
WARNING WARNING TEMP. FILTER SHUTTER LAMP 1/2 REP. red orange blue orange Projector Condition ✽ Fig.2 Filter replacement icon Fig.3 Fig.4 Filter cartridge replacement icon If the Filter counter reached a time set in the timer ✽ setting, a Filter replacement icon (Fig.2) appears - Sanyo PLC-XF71 | Owners Manual - Page 75
Appendix Compatible Computer Specifications Basically this projector can accept the signal from all SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA 15 MAC 19 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 RESOLUTION - Sanyo PLC-XF71 | Owners Manual - Page 76
signal is digital from the DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 8 D-WXGA 9 these signals may not be properly viewed. •Specifications are subject to change without notice. 76 - Sanyo PLC-XF71 | Owners Manual - Page 77
) Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label Lens Attachments (2 types) (For option lens) Light Block Plates (3 types) (For option lens) Spacer (For option lens) Real Color Manager Pro (CD-ROM) Mounting Clamp 77 - Sanyo PLC-XF71 | Owners Manual - Page 78
● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD panels. ● Each projector has - Sanyo PLC-XF71 | Owners Manual - Page 79
Configurations of Terminals ANALOG (Mini D-sub 15 pin) 54 32 1 10 9 8 7 6 15 14 13 12 11 1 Red Input 2 Green Input 3 Blue Input 4 No Connect 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) 9 +5V Power 10 Ground (Vert. sync.) 11 Ground 12 DDC Data 13 Horiz. sync. 14 Vert. - Sanyo PLC-XF71 | Owners Manual - Page 80
Number Memo Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Logo PIN Code Lock No. Factory default set No: 1 2 3 4* Factory default set - Sanyo PLC-XF71 | Owners Manual - Page 81
Dimensions Unit: inch (mm) 20.87(530) 4.72(120) 5.81(147.5) 9.63(244.5) 10.53(267.5) Appendix Screw Holes for Ceiling Mount Screw: M8 Depth: 0.393 (10.0) 8.66(220) 8.46(215) 1.18(30) 5.00(127) 3.03(77) 10.43(265) 6.89(175) 8.27(210) 7.28(185) 23. - Sanyo PLC-XF71 | Owners Manual - Page 82
C05 C06 C07 C08 C0D C0E C0F C10 C1C C1D C3A Function Turn the projector ON Turn the projector OFF (immediately OFF) Select Input 1 Select Input 2 Select Input 3 Select DOWN Focus UP Lens shift UP Lens shift DOWN Lens shift LEFT Lens shift RIGHT Auto PC Adj. Keystone UP Keystone DOWN - Sanyo PLC-XF71 | Owners Manual - Page 83
command. Cooling down at Power Management mode Power Management mode after Cooling down Cooling down after the projector is turned off when the lamps are out. Stand-by mode after Cooling down when the lamps are out. Stand-by mode after Cooling down at the temperature anomaly. Cooling down when the - Sanyo PLC-XF71 | Owners Manual - Page 84
KW7A SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
 |
 |
Multimedia Projector
MODEL
PLC-XF71
Owner’s Manual
✽
Projection lens is optional.