Sanyo PLC-XK2600 Owner's Manual Network

Sanyo PLC-XK2600 - 2600 Lumens Manual

Get Sanyo PLC-XK2600 - 2600 Lumens PDF manuals and user guides
UPC - 086483079504
View all Sanyo PLC-XK2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Sanyo PLC-XK2600 manual content summary:

  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 1
    This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 2
    otherwise speci- fied in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-XK2200, PLC-XK2600, PLC-XK3010 Trade Name : Sanyo Responsible party : SANYO NORTH AMERICA CORPORATION Address : 21605
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 3
    Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 4
    instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector setting...25 Examples: Type and contents of alert mail 28 SNMP setting...29 Chapter 4 Controlling the Projector 31 Power control and
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 5
    Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH 
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 6
    sages to the registered e-mail PC1 PC2 addresses when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You can take efficient action for quick recovery. PJ2 PJ1 PC5 Turn ON PJ2 PC6 PJ2 PJ1 PC5
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 7
    Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 control and set up the projector. The layout of pages in the browser may slightly differ from each type of application or operating system
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 8
    when connecting the projector and a hub or computer. Connection Projector - Hub Projector - Computer Ethernet cable type STP straight-through manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 9
    pp.11-16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projectors, then start browser configurations. ➔ "3. Basic setting and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 10
    Chapter 1 Preparation 10
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 11
    Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 12
    is connected to the network correctly. LAN Cable * Please use a shielded LAN cable. Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to "3. Basic setting and operation" (p.17-30). First, complete the settings
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 13
    DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 14
    "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 15
    Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 16
    Chapter 2 Setup Procedures Wired LAN factory default settings Parameter LAN 1 SELECTED LAN LAN 2 LAN 3 DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 17
    Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 18
    setting page has set the password, the authentication window will appear. In this case type "user" onto the User Name text area and the login Network PIN code onto be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 19
    Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 20
    set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab. * Each item has a valid setting range respectively. Types
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 21
    Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 22
    display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector SERIAL NO. ..........Indicates the serial number of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 23
    System Industries Association (JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 24
    in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. Item Description
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 25
    1 to 65535) Administrator address....Enter e-mail address of administrator. Add address Enter e-mail address of the user to send mail when the projector has an abnormality. SMTP Authentication setting Auth Sets authentication setting option. (Off, SMTP Auth, POP before SMTP) SMTP Auth Sets user
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 26
    setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 27
    mail will be sent and click Set button. Please refer to item "Examples :Type and contents of alert mail" described on the next page. Option ENGLISH ✐ When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 28
    Basic Setting and Operation Examples: Type and contents of alert mail When the projector has an abnormality, the following then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 29
    SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 30
    PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 31
    Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 32
    starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The projector cannot be turned on while the projector is on cooling down. ✐ The
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 33
    standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel.  When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 34
    differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 35
    System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 36
    Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume through the network. When using the MIC functions, please set by using the On Screen Menu of the projector. 36
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 37
    Control Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast Adjusts picture contrast (0~ 63) Brightness Adjusts picture
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 38
    PC adjustment Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 39
    the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item Description Screen Switches the screen mode. (Normal, Full, Wide(16:9), Zoom
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 40
    , ON2, OFF) Auto keystone.....Sets Auto Keystone mode. (Auto, Manual, OFF) Background.........Sets the screen background when no signal input. (Blue Eco) Key lock Sets the prohibition of controls either Projector or Remote control. (OFF, Projector keys, Remote control) Fan control Sets the fan
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 41
    Filter warning.....Sets the time to indicate the filter warning message on the screen. (OFF, 2000H, 3000H, 4000H) Factory default....Sets all of the projector control items to the factory default setting except the following items. User Logo, Log PIN code lock, PIN code lock, Lamp Corres. Value
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 42
    table as shown below. Security Displays the security (PIN code lock) status (Yes, No) PJ time(h) Displays the accumulated use time of the projector. Lamp Corres. Value(h) Displays the use time (Corresponding value) of the lamp. Filter time(h) Displays the accumulated use time of the filter
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 43
    Information Indication of the lamp status Icon display/background Status White/Blue Lamp on (Normal) White/Red Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Gray/Blue Gray/Red Lamp off (Normal) Lamp off (Lamp is being used over a specified use time, replace
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 44
    Chapter 4 Controlling the Projector 44
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 45
    Chapter 5 Appendix Connection examples Use of telnet Web browser setting Q & A 5 ENGLISH 45
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 46
    the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 47
    . Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 48
    Mac OS X v 10.4) 1. Select Terminal from Applications -->Utilities. Type as below on the displayed window. > telnet [return] 2. The telnet application will start and the following window will be displayed. Type as below to connect the projector. > open 192.168.1.201 10000 [return] *U se the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 49
    the word "PASSWORD:" appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard on C1D Menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 50
    is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 51
    Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 52
    proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 53
    to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 54
    address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 55
    status (☞ p.12). - Check the connection of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong network configuration of the computer. Check the network configuration of the computer. 3. The proxy
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 56
    Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 57
    take a lot of time to complete the page display? A The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if network traffic is heavy. Please consult your network administrator
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 58
    , they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.48 - 49). Q What is the MAC address assigned to
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 59
    Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult
  • Sanyo PLC-XK2600 | Owner's Manual Network - Page 60
    NETWORK OWNER'S MANUAL SO-KT8AE SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.